← The Saudi aviation reference, in one place.
Weight and Balance Handbook (FAA-H-8083-1B)
Reproduced for study. Always verify against the official GACAR at gaca.gov.sa.
Aircraft
Weight and Balance
Handbook
U.S. Department of Transportation
FEDERAL AVIATION ADMINISTRATION
Flight Standards Service
ii
iiiThe Aircraft Weight and Balance Handbook has been prepared in recognition of the importance of weight and balance
technology in conducting safe and efficient flight. The objective of this handbook is twofold: to provide the airframe and powerplant mechanic (A&P) with the method of determining the empty weight and empty weight center of gravity (EWCG) of an aircraft and to furnish the flight crew with information on loading and operating the aircraft to ensure its weight is within the allowable limit and the center of gravity (CG) is within the allowable range.
Any time there is a conflict between the information in this handbook and specific information issued by an aircraft
manufacturer, the manufacturer’s data takes precedence over information in this handbook. Occasionally, the word “must” or similar language is used where the desired action is deemed critical. The use of such language is not intended to add to, interpret, or relieve a duty imposed by Title 14 of the Code of Federal Regulations (14 CFR).
It is essential for persons using this handbook to become familiar with and apply the pertinent parts of 14 CFR. The current
Flight Standards Service airman training and testing material and learning statements for all airman certificates and ratings can be obtained from www.faa.gov.
This handbook supersedes FAA-H-8083-1A, Aircraft Weight and Balance Handbook, dated 2007. This handbook is available for download, in PDF format, from www.faa.gov.This handbook is published by the United States Department of Transportation, Federal Aviation Administration, Airman
Testing Standards Branch, AFS-630, P.O. Box 25082, Oklahoma City, OK 73125.
Comments regarding this publication should be sent, in email form, to the following address:AFS630comments@faa.gov.
John S. Duncan
Director, Flight Standards Service
Preface
iv
vThis handbook begins with the basic principle of aircraft weight and balance control, emphasizing its importance and
including examples of documentation furnished by the aircraft manufacturer and by the FAA to ensure the aircraft weight and balance records contain the proper data.
Procedures for the preparation and the actual weighing of an aircraft are described, as are the methods of determining the
location of the empty weight center of gravity (EWCG) relative to both the datum and the mean aerodynamic chord (MAC).
Loading computations for general aviation aircraft are discussed using both loading graphs and tables of weight and
moment indexes.
Information is included that allows an FAA-certifi ated mechanic or repairman to determine the weight and center of gravity
(CG) changes caused by repairs and alterations or removal and installation of equipment. This includes instructions for conducting adverse-loaded CG checks, also explaining the way to determine the amount and location of ballast needed to bring the CG within allowable limits.
The unique requirements for helicopter weight and balance control are discussed, including the determination of lateral CG
and the way both lateral and longitudinal CG change as fuel is consumed.
One chapter includes the methods and examples of solving weight and balance problems using a hand-held electronic
calculator, E6-B flight computer, and a dedicated electronic flight compute
Introduction
vi
viiThe Aircraft Weight and Balance Handbook (FAA-H-8083-1B) was produced by the Federal Aviation Administration
(FAA) with the assistance of Safety Research Corporation of America (SRCA). The FAA wishes to acknowledge the following contributors:
Larry Jackson of Jackson Aircraft Weighing Service, for content and photographs used in Chapter 3
The White Planes Picture Company (www.whiteplanes.com), for images used in Chapter 4
Terri Sipantzi of Precision Windsports, for the weight-shift control sample weight and loading diagram used in Chapter 4
AirBorne Windsports Pty Ltd., for weight-shift control sample weight and loading data sheet used in Chapter 4
Jim Stevens of Aerosports Connection, for powered parachute sample weight and balance information sheet used in
Chapter 4
Sporty’s Pilot Shop, for image of an E6B Flight Computer used in Chapter 10
Acknowledgments
viii
ixPreface .................................................................... iii
Introduction ............................................................. v
Acknowledgments ................................................ vii
Table of Contents .................................................. ix
Chapter 1
Weight and Balance Control ............................... 1-1
Introduction .................................................................... 1-1
Responsibility for Weight and Balance Control ............ 1-2
Terminology ................................................................... 1-2
Weight Control .............................................................. 1-2
Effects of Weight ........................................................... 1-3
Weight Changes ............................................................. 1-3
Stability and Balance Control ........................................ 1-4
Weight Control for Aircraft Other Than Fixed and Rotor-wing
..................................................................... 1-5
Weight-Shift Control Aircraft .................................... 1-5
Powered Parachutes .................................................... 1-6
Balloons ...................................................................... 1-6
Underestimating the Importance of Weight and Balance
........................................................................... 1-6
Chapter 2Weight and Balance Theory
............................... 2-1
Introduction .................................................................... 2-1
Weight and Balance Theory ........................................... 2-2
Arm ............................................................................ 2-2
Moment ...................................................................... 2-2
The Law of the Lever ..................................................... 2-2
Shifting the Balance Point or CG ................................... 2-4
Solution by Chart ....................................................... 2-4
Basic Weight and Balance Equation .......................... 2-4
Solution by Formula ................................................... 2-5
Mean Aerodynamic Chord ............................................. 2-5
FAA-Furnished Weight and Balance Information ........ 2-6
CG Range ................................................................... 2-6
Empty Weight CG Range (EWCG) ........................... 2-6Maximum Weights ..................................................... 2-6
Number of Seats ......................................................... 2-6
Maximum Baggage ................................................... 2-6
Fuel Capacity .............................................................. 2-6
Oil Capacity (Wet Sump) ........................................... 2-6
Data Pertinent to all Models ..................................... 2-10
Manufacturer-Furnished Information .......................... 2-10
Chapter 3Weighing the Aircraft and Determining the Empty Weight Center of Gravity
........................ 3-1
Introduction .................................................................... 3-1
Requirements ................................................................. 3-2
Equipment for Weighing ................................................ 3-2
Preparation for Weighing ............................................... 3-3
Scale Preparation ........................................................ 3-3
Weigh Clean Aircraft Inside Hangar .......................... 3-4
Equipment List ........................................................... 3-4
Ballast ......................................................................... 3-4
Standard Weights ....................................................... 3-4
Draining the Fuel ........................................................ 3-4
Oil ............................................................................... 3-4
Other Fluids ................................................................ 3-4
Configuration of the Aircraf ...................................... 3-5
Jacking the Aircraft .................................................... 3-5
Leveling the Aircraft .................................................. 3-5
Safety Considerations ................................................. 3-5
Determining the CG ....................................................... 3-5
EWCG Formulas ............................................................ 3-6
Datum Forward of the Airplane—Nosewheel Landing Gear
.............................................................. 3-6
Datum Aft of the Main Wheels—Nosewheel Landing Gear
.............................................................. 3-6
Location of Datum ......................................................... 3-7
Datum Forward of the Main Wheels—Tailwheel
Landing Gear .............................................................. 3-7
Datum Aft of the Main Wheels—Tailwheel
Landing Gear .............................................................. 3-7
Center of Gravity (CG) and Mean Aerodynamic Chord (MAC)
................................................................. 3-8
Table of Contents
xCenter of Gravity (CG) ............................................... 3-8
Mean Aerodynamic Chord (MAC) ............................ 3-8
Chapter 4
Light Sport Aircraft Weight and Balance Control
.................................................................. 4-1
Introduction .................................................................... 4-1
LSA Definition of Term ............................................ 4-2
Weight and Balance ....................................................... 4-3
WSC Aircraft .............................................................. 4-3
Powered Parachutes .................................................... 4-4
Weight and Balance Computations (Amateur-Built
Aircraft) .......................................................................... 4-4
Chapter 5
Single-Engine Aircraft Weight and Balance
Computations ...................................................... 5-1
Introduction .................................................................... 5-1
Determining the Loaded Weight and CG ...................... 5-2
Manual Computational Method .................................. 5-2
Loading Graph Method .............................................. 5-4
Moment Indexes ..................................................... 5-4
Loading Graph ........................................................ 5-4
Compute Weight and Balance Using the
Loading Graph ........................................................ 5-4
Chapter 6
Multiengine Aircraft Weight and Balance
Computations ...................................................... 6-1
Introduction .................................................................... 6-1
Determine the Loaded CG ............................................. 6-2
Chart Method Using Weight, Arm, and Moments .....6-2
Determining the CG in Percentage of Mean Aerodynamic Chord (MAC)
...................................... 6-3
The Chart Method Using Weight and
Moment Indexes ......................................................... 6-3
Chapter 7Center of Gravity Change After a Repair or Alteration
............................................. 7-1
Introduction .................................................................... 7-1
Equipment List ............................................................... 7-2
Major Alteration and Repair .......................................... 7-3
Weight and Balance Revision Record ........................... 7-3
Weight Changes Caused by a Repair or Alteration .......7-5
Computations Using Weight, Arm, and Moment .......7-5
Computations Using Weight and Moment Indexes ...7-5
Determining the CG in Percentage of Mean
Aerodynamic Chord (Percent MAC) ......................... 7-6
Empty Weight CG (EWCG) Range ............................... 7-6
Adverse-Load CG Checks ............................................. 7-6
Forward Adverse-Load CG Check ............................. 7-7
Aft Adverse-Load CG Check ..................................... 7-7Ballast ............................................................................ 7-7
Temporary Ballast ...................................................... 7-8
Temporary Ballast Formula ........................................ 7-8
Permanent Ballast ....................................................... 7-8
Chapter 8
Weight and Balance Control—Helicopter ......... 8-1
Introduction .................................................................... 8-1
Determining the Loaded CG of a Helicopter ................. 8-3
Effects of Offloading Passengers and Using Fue .......... 8-3
Chapter 9Weight and Balance Control—Commuter
Category and Large Aircraft
............................... 9-1
Introduction .................................................................... 9-1
Establishing the Initial Weight of an Aircraft ............... 9-2
Determining the Empty Weight and Empty Weight
CG (EWCG) ................................................................... 9-2
Documenting Changes to an Aircraft’s Weight and
Balance .......................................................................... 9-3
Determining the Loaded CG of the Airplane in
Percent MAC ................................................................. 9-3
Operational Empty Weight (OEW) ............................... 9-5
Reestablishing the OEW ............................................ 9-5
Fleet Operating Empty Weights (FOEW) ................. 9-5
Onboard Aircraft Weighing System ........................... 9-5
Determining the Correct Stabilizer Trim Setting .......9-6
Determining CG Changes Caused by Modifying the Cargo
.............................................................................. 9-6
Effects of Loading or Offloading Cargo .................... 9-6
Effects of Shifting Cargo From One Hold to Another
....................................................................... 9-8
Determining Cargo Pallet Loads and Floor Loading Limits
........................................................... 9-9
Determining the Maximum Amount of Payload That Can Be Carried
................................................. 9-10
Determining the Landing Weight ............................. 9-10
Determining Fuel Dump Time in Minutes ............... 9-12
Weight and Balance of Commuter Category Airplanes
.................................................................. 9-12
Determining the Loaded Weight and CG ................. 9-12
Determining the Changes in CG When Passengers Are Shifted
............................................................... 9-16
Determining Changes in Weight and CG When the Aircraft Is Operated in Its Cargo Configuratio
............................................................ 9-18
Determining the CG Shift When Cargo Is Moved From One Section to Another
.................................. 9-18
Determining the CG Shift When Cargo Is Added or Removed
.............................................................. 9-18
Determining Which Limits Are Exceeded ............... 9-18
xiChapter 10
Use of Computer for Weight and Balance
Computations .................................................... 10-1
Introduction .................................................................. 10-1
Electronic Calculator ................................................... 10-2
E6-B Flight Computer .................................................. 10-2
Dedicated Electronic Flight Computer ........................ 10-3
Typical Weight and Balance Problems .................... 10-4
Determining CG in Inches From the Datum ............ 10-4
Nosewheel Airplane With Datum Ahead of the
Main Wheels ......................................................... 10-4
Nosewheel Airplane With Datum Behind the Main Wheels
......................................................... 10-4
Tailwheel Airplane With Datum Ahead of the Main Wheels
......................................................... 10-4
Tailwheel Airplane With Datum Behind the Main Wheels
......................................................... 10-4
Determining CG, Given Weights, and Arms ........... 10-5
Determining CG, Given Weights, and Moment
Indexes ...................................................................... 10-5
Determining CG in Percent Mean Aerodynamic Chord (MAC)
........................................................... 10-5
Determining Lateral CG of a Helicopter .................. 10-5
Determining ΔCG Caused by Shifting Weights .......10-6
Determining Weight Shifted to Cause SpecifiedΔCG
.......................................................................... 10-6
Determining Distance Weight Is Shifted to Move CG a Specific Distanc
............................................. 10-6
Determining Total Weight of an Aircraft With a
Specified ΔCG When Cargo Is Move .................... 10-7
Determining Amount of Ballast Needed to Move
CG to a Desired Location ......................................... 10-7Appendix A .......................................................... A-1
Appendix B .......................................................... B-1
Glossary .............................................................. G-1
Index ...................................................................... I-1
xii
Introduction
There are many factors in the safe and efficient operation of
aircraft, including proper weight and balance control. The weight and balance system commonly employed among aircraft consists of three equally important elements: the weighing of the aircraft, the maintaining of the weight and balance records, and the proper loading of the aircraft. An inaccuracy in any one of these elements defeats the purpose of the system. The final loading calculations are meaningless if either the aircraft has been improperly weighed or the records contain an error.
Improper loading decreases the effic ency and performance of
an aircraft from the standpoint of altitude, maneuverability, rate of climb, and speed. It may even be the cause of failure to complete the flight or, for that matter, failure to start the flight. Because of abnormal stresses placed upon the structure of an improperly loaded aircraft, or because of changed fly ng characteristics of the aircraft, loss of life and destruction of valuable equipment may result.
Weight and Balance
ControlChapter 1
1-2Aircraft can perform safely and achieve their designed
efficiency only when they are operated and maintained in the way their designers intended. This safety and efficiency is
determined to a large degree by holding the aircraft’s weight and balance parameters within the limits specified for its design. The remainder of this handbook describes how this is done.
Responsibility for Weight and Balance
Control
The responsibility for proper weight and balance control
begins with the engineers and designers and extends to the
technicians who maintain the aircraft and the pilots who operate them. Modern aircraft are engineered utilizing state-of-the-art technology and materials to achieve maximum reliability and performance for the intended category. As much care and expertise must be exercised in operating and maintaining these efficient aircraft as was taken in their design and manufacturing:
1. The designers of an aircraft set the maximum weight
based on the amount of lift the wings or rotors can provide under the operational conditions for which the aircraft is designed. The structural strength of the aircraft also limits the maximum weight the aircraft can safely carry. The designers carefully determine the ideal center of gravity (CG) and calculate the maximum allowable deviation from this specific location.
2. The manufacturer provides the aircraft operator with
the empty weight of the aircraft and the location of its empty weight center of gravity (EWCG) at the time the certified aircraft leaves the factory. Amateur-built aircraft must have this information determined and available at the time of certification
3. The FAA-certificated mechanic or repairman who
maintains the aircraft keeps the weight and balance records current, recording any changes that have been made because of repairs or alterations.
4. The pilot in command (PIC) has the responsibility
prior to every flight to know the maximum allowable weight of the aircraft and its CG limits. This allows the pilot to determine during the preflight inspection that the aircraft is loaded so that the CG is within the allowable limits.
Terminology
Pilots and FAA-certificated mechanics or repairmen must ensure they understand the terms as they relate to the aircraft in question. For small aircraft terminology, use the information found in sources associated with Civil Air Regulation (CAR) 3 certification or General Aviation Manufacturers Association (GAMA) Specification No. 1 for part 23 aircraft or part 27 for rotorcraft. For terminology applied to large part 25 aircraft, information can be found in Advisory Circular (AC) 120-27, Aircraft Weight and Balance Control. The glossary contains the most current terms and defin tions. Current regulations are available from the Superintendent of Documents; U.S. Government Printing Office; Washington, DC 20402. They are also located on the FAA website at www.faa.gov. Earlier regulations may be available in libraries or in the Federal Register.
Weight Control
Weight is a major factor in airplane construction and operation, and it demands respect from all pilots and particular diligence by all maintenance personnel. Excessive weight reduces the efficiency of an aircraft and the available safety margin if an emergency condition should arise.
When an aircraft is designed, it is made as light as the
required structural strength allows, and the wings or rotors are designed to support the maximum allowable weight. When the weight of an aircraft is increased, the wings or rotors must produce additional lift and the structure must support not only the additional static loads, but also the dynamic loads imposed by flight maneuvers. For example, the wings of a 3,000-pound airplane must support 3,000 pounds in level flight, but when the airplane is turned smoothly and sharply using a bank angle of 60°, the dynamic load requires the wings to support twice this or 6,000 pounds.
Severe uncoordinated maneuvers or flight into turbulence
can impose dynamic loads on the structure great enough to cause failure. In accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 23, the structure of a normal category airplane must be strong enough to sustain a load factor of 3.8 times its weight. Every pound of weight added to a normal category aircraft requires that the structure be strong enough to support 3.8 pounds. An aircraft operated in the utility category must sustain a load factor of 4.4 times its weight, and acrobatic category aircraft must be strong enough to withstand 6.0 times their weight.
The lift produced by a wing is determined by its airfoil shape,
angle of attack, speed through the air, and air density. When
an aircraft takes off from an airport with a high density altitude, it must accelerate to a speed faster than would be required at sea level to produce enough lift to allow takeoff; therefore, a longer takeoff run is necessary. The distance needed may be longer than the available runway. When operating from a high density altitude airport, the Pilot’s Operating Handbook (POH) or Airplane Flight Manual (AFM) must be consulted to determine the maximum weight allowed for the aircraft under the conditions of altitude, temperature, wind, and runway conditions.
1-3Effects of Weight
Most modern aircraft are so designed that, when all seats
are occupied, the baggage compartment is full, and all fuel tanks are full, the aircraft is grossly overloaded. This type of design requires the pilot to give great consideration to the requirements of each specific flight. If maximum range is required, occupants or baggage must be left behind, or if the maximum load must be carried, the range, dictated by the amount of fuel on board, must be reduced.
Overloading an aircraft can create a variety of problems:
• The aircraft needs a higher takeoff speed, which results
in a longer takeoff run.
• Both the rate and angle of climb are reduced.
• The service ceiling is lowered.
• The cruising speed is reduced.
• The cruising range is shortened.
• Maneuverability is decreased.
• A longer landing roll is required because the landing
speed is higher.
• Excessive loads are imposed on the structure,
especially the landing gear.
The POH or AFM includes tables or charts that give the pilot
an indication of the performance expected for any weight. An important part of careful preflight planning includes a check of these charts to determine if the aircraft is loaded so the proposed flight can be safely made
Weight Changes
The maximum allowable weight for an aircraft is determined by design considerations. However, the maximum operational weight may be less than the maximum allowable weight due to such considerations as high density altitude or high-drag field conditions caused by wet grass or water on the runway. The maximum operational weight may also be limited by the departure or arrival airport’s runway length.
One important preflight consideration is the distribution
of the load in the aircraft. Loading the aircraft so the gross weight is less than the maximum allowable is not enough. This weight must be distributed to keep the CG within the limits specified in the POH or AFM
If the CG is too far forward, a heavy passenger can be moved
to one of the rear seats or baggage may be shifted from a forward baggage compartment to a rear compartment. If the CG is too far aft, passenger weight or baggage can be shifted forward. The fuel load should be balanced laterally. The pilot should pay special attention to the POH or AFM regarding the operation of the fuel system in order to keep the aircraft balanced in flight
Weight and balance of a helicopter is far more critical
than for an airplane. Some helicopters may be properly loaded for takeoff, but near the end of a long flight when the fuel tanks are almost empty, the CG may have shifted enough for the helicopter to be out of balance laterally or longitudinally. Before making any long flight, the CG with the fuel available for landing must be checked to ensure it is within the allowable range.
Airplanes with tandem seating normally have a limitation
requiring solo flight to be made from the front seat in some airplanes or the rear seat in others. Some of the smaller helicopters also require solo flight be made from a specificseat, either the right, left, or center. These seating limitations are noted by a placard, usually on the instrument panel, and they should be strictly followed.
As an aircraft ages, its weight usually increases due to debris
and dirt collecting in hard-to-reach locations and moisture absorbed in the cabin insulation. This increase in weight is normally small, but it can be determined only by accurately weighing the aircraft.
Changes of fixed equipment may have a major effect upon
the weight of the aircraft. Many aircraft are overloaded by the installation of extra radios or instruments. Fortunately, the replacement of older, heavy electronic equipment with newer, lighter types results in a weight reduction. This weight change, however helpful, can cause the CG to shift, which must be computed and annotated in the weight and balance record.
Repairs and alterations are the major sources of weight
changes. It is the responsibility of the FAA-certificate mechanic or repairman making any repair or alteration to know the weight and location of a change, to compute the CG, record the new empty weight and EWCG in the aircraft weight and balance record, and update the equipment lists.
If the newly calculated EWCG should happen to fall outside
the EWCG range, it is necessary to perform an adverse-loading check. This requires a forward and rearward adverse-loading check and a maximum weight check. These weight and balance extreme conditions represent the maximum forward and rearward CG position for the aircraft. An adverse-loading check is a deliberate attempt to load an aircraft in a manner that creates the most critical balance condition and still remains within the design CG limits of the aircraft. If any of the checks fall outside the loaded CG range,
1-4Figure 1-1. Longitudinal forces acting on an airplane in flight.Lift
Variable
Nose-up force
dependent upon airspeed Fixed
Nose-down force
independent of airspeedCGFigure 1-2. If the CG is too far aft at the low stall airspeed, there
might not be enough elevator nose-down authority to get the nose
down for recovery.Lift
Insufficient elevator
Nose-down force
CG too far aftCG
Figure 1-3. If the CG is too far forward, there is not enough elevator
nose-up force to flare the airplane for landing.Lift
Insufficient elevator
Nose-up force
CG too far forwardCGthe aircraft must be reconfigured or placarded to prevent the
pilot from loading the aircraft improperly. It is sometimes
possible to install a fixed ballast in order for the aircraft to operate again within the normal CG range.
The FAA-certificated mechanic or repairman conducting an
annual or condition inspection must ensure the weight and balance data in the aircraft records is current and accurate. It is the responsibility of the PIC to use the most current weight and balance data when operating the aircraft.
Stability and Balance Control
Balance control refers to the location of the CG of an aircraft. This is of primary importance to aircraft stability, which is a factor in flight safety. The CG is the point at which the total weight of the aircraft is assumed to be concentrated, and the CG must be located within specific limits for safe flight. Both lateral and longitudinal balance are important, but the prime concern is longitudinal balance; that is, the location of the CG along the longitudinal or lengthwise axis.
An airplane is designed to have stability that allows it to be
trimmed to maintain straight-and-level flight with hands off the controls. Longitudinal stability is maintained by ensuring the CG is slightly ahead of the center of lift. This produces a fixed nose-down force independent of the airspeed. This is balanced by a variable nose-up force, which is produced by a downward aerodynamic force on the horizontal tail surfaces
that varies directly with the airspeed. [Figure 1-1]
If a rising air current should cause the nose to pitch up, the
airplane slows and the downward force on the tail decreases. The weight concentrated at the CG pulls the nose back down. If the nose should drop in flight, the airspeed increases and the increased downward tail load brings the nose back up to level flight
As long as the CG is maintained within the allowable limits
for its weight, the airplane has adequate longitudinal stability and control. If the CG is too far aft, it is too near the center of lift; the airplane is unstable and difficult to recover from a stall. [Figure 1-2] If the unstable airplane should enter a
spin, the spin could become flat making recovery difficultor impossible. If the CG is too far forward, the downward tail load needs to be increased to maintain level flight. This increased tail load has the same effect as carrying additional weight; the aircraft must fly at a higher angle of attack and drag increases.
A more serious problem caused by the CG being too far
forward is the lack of sufficient elevator authority. At low takeoff speeds, the elevator might not produce enough nose-up force to rotate; on landing there may not be enough elevator force to flare the airplane. [Figure 1-3] Both takeoff
and landing runs are lengthened if the CG is too far forward.The basic aircraft design is such that lateral symmetry is assumed to exist. For each item of weight added to the left of the center line of the aircraft (also known as buttock
line zero or BL -0), there is generally an equal weight at a
corresponding location on the right.
The lateral balance can be upset by uneven fuel loading
or burnoff. The position of the lateral CG is not normally
computed for an airplane, but the pilot must be aware of
1-5Figure 1-4. Lateral imbalance causes wing heaviness, which may
be corrected by deflecting the aileron. The additional lift causes
additional drag, and the airplane flies inefficiently.
Empty Full
Additional lift and drag
Additional weight
Figure 1-5. Fuel in the tanks of a swept-wing airplane affects both
lateral and longitudinal balance. As fuel is used from an outboard tank, the CG shifts forward.
Inboard fuel: nose heavyOutboard fuel: tail heavythe adverse effects that result from a laterally unbalanced
condition. [Figure 1-4] This is corrected by using the aileron
trim tab until enough fuel has been used from the tank on
the heavy side to balance the airplane. The deflected trim tab deflects the aileron to produce additional lift on the heavy side, but it also produces additional drag, and the airplane flies inefficientl
Helicopters are more often affected by lateral imbalance
than airplanes. If a helicopter is loaded with heavy occupants and fuel on the same side, it could be out of balance enough to make it unsafe to fly. It is also possible that if external loads are carried in such a position that requires large lateral displacement of the cyclic control to maintain level fl ght, the fore-and-aft cyclic control effectiveness is limited.
Swept-wing airplanes are more critical due to fuel imbalance
because as the fuel is used from the outboard tanks, the CG shifts forward. As fuel is used from the inboard tanks, the CG shifts aft. [Figure 1-5] For this reason, fuel-use scheduling
in swept-wing airplanes operation is critical.
Weight Control for Aircraft Other Than
Fixed and Rotor-wing
Some light aircraft utilize different methods of determining
weight and balance from the traditional fixed and rotor-wing
aircraft. These aircraft achieve flight control by methods different from the fixed-wing airplane or helicopter. Most notable of these are weight-shift control (WSC) aircraft (also
known as trikes), powered parachutes, and balloons. These
aircraft typically do not specify either an EWCG or a CG range. They require only a certified or approved maximum weight. To understand why this is so, a look at how flightcontrol is achieved is helpful.
Airplanes and WSC aircraft control flight under the influenc
of the same four forces (lift, gravity, thrust, and drag), and around the same three axes (pitch, yaw, and roll). However, each aircraft accomplishes this control in a very different manner. This difference helps explain why the fixed-wingairplane requires an established weight and a known CG, whereas the WSC aircraft only requires the known weight.
The fixed-wing airplane has movable controls that alter lift
on various airfoil surfaces to vary pitch, roll, and yaw. In
turn, these changes in lift affect the characteristics of the flight parameters. Weight normally decreases in flight due to fuel consumption, and the airplane CG changes with this weight reduction. An airplane utilizes its variable fligh controls to compensate and maintain controllability through the various flight modes and as the CG changes. An airplane has a CG range or envelope within which it must remain if the flight controls are to remain effective and the airplane safely operated.
Weight-Shift Control Aircraft
The WSC aircraft has a relatively set platform wing without
a tail. The pilot achieves control by shifting weight. In the design of this aircraft, the weight of the airframe and its payload is attached to the wing at a single point in a pendulous arrangement. The pilot, through the flight controls, controls the
arm of this pendulum and thereby controls the aircraft. When a change in flight parameter is desired, the pilot displaces the aircraft’s weight by the appropriate distance and direction. This change momentarily disrupts the equilibrium between the four forces acting on the aircraft. The wing, due to its inherent stability, then moves appropriately to reestablish the desired relationship between these forces; the wing flexes and alter its shape. As the shape is changed, lift is varied at different points on the wing to achieve the desired flight parameters
1-6The flight controls primarily affect the pitch-and-roll axes.
Since there is no vertical tail plane, there is minimal or no yaw control. Unlike in an airplane, the CG experienced by the WSC aircraft wing remains constant. Since the weight of the airframe acts through a single point (the wing attach point), the range over which the weight may act is fixed at the pendulum arm or length. Even though weight decreases as fuel is consumed, weight remains focused at the wing attach point. Because the range is fixed, there is no need to establish a calculated range. The pilot should consult the POH or Aircraft Operating Instructions (AOI) for maximum takeoff weight and minimum and maximum seat weight limits prior to each flight
Powered Parachutes
The powered parachute is also a pendulum-style aircraft. Its
airframe CG is fixed at the pendulum attach point. It is more
limited in controllability than the WSC aircraft because it lacks an aerodynamic pitch control. Pitch (and lift) control is primarily a function of the power control. Increased power results in increased lift; cruise power amounts to level flight;decreased power causes a descent. Due to this characteristic, the aircraft is basically a one-airspeed aircraft. Once again, because the CG is fixed at the attach point to the wing, there is no CG range. As with WSC, the pilot should consult the POH or AOI for maximum takeoff weight and minimum and maximum seat weight limits prior to each flight
Roll control on a powered parachute is achieved by changing
the shape of the wing. The change is achieved by varying the length of steering lines attached to the outboard trailing edges of the wing. The trailing edge of the parachute is pulled down slightly on one side or the other to create increased drag along that side. This change in drag creates roll and yaw, permitting the aircraft to be steered.
Balloons
The balloon is controlled by the pilot only in the vertical
dimension; this is in contrast to all other aircraft. He or she
achieves this control through the use of lift and weight. Wind provides all other movement. The CG of the gondola remains constant beneath the balloon envelope. As in WSC and powered-parachute aircraft, there is no CG limitation.
Underestimating the Importance of
Weight and Balance
Many pilots, from sport pilot to commercial pilot, tend to
underestimate the importance of proper weight and balance of their aircraft. Load sheets are taken for granted and hasty calculations are made of the aircraft’s CG. Unfortunately, each year there are a number of accidents related to weight and balance issues. Many of these occurrences could have been avoided had more attention been given to weight and balance.Every student pilot is taught how to work a weight and balance problem and that it is important to make sure every flight is loaded “within the envelope” (no more than maximum gross weight) for both takeoff and landing. But does he or she really understand just why this is so and the disastrous effect of being out of the envelope? Two examples of documented cases are provided below in an effort to indicate the serious nature of maintaining the proper weight and balance. In case studies when weight and balance was listed as the major factor of the accident, many were fatal.
For instance, a small aircraft was loaded with hunters, gear,
and dogs (none of the dogs were secured inside the aircraft). During takeoff, all the dogs went to the aft of the airplane. This shifted the CG well aft of its allowable limit. The airplane stalled and crashed. The airplane was destroyed with casualties.
Another accident occurred when a group of skydivers were
sitting on the floor toward the aft portion of the airplane (they were unsecured). During takeoff, the CG was again well beyond its aft limit. The airplane stalled and crashed. The airplane was destroyed with casualties.
There is a safety factor built into the formula for maximum
gross weight. Any airplane can fly when it takes off at a
weight greater than maximum gross weight if the runway is long enough and the density altitude is low enough. However, landing is a different matter. All airplanes are built to withstand an occasional hard landing, but what would happen if the hard landing were combined with a substantially overweight airplane? Something would probably break at that time or the structure would be weakened enough to break sometime in the future when everything might seem normal to a pilot unaware of the previous situation. Even more disastrous than an overweight, hard landing is reaching or exceeding the structural integrity of the metal and/or composite design values when maneuvering or when turbulence is encountered. Hidden damage could result, causing an unexpected catastrophic failure at some future time.
If an airplane is certificated with a maximum gross weight
of 6,000 pounds (its weight on the ground) and is rolled into a 60° bank, the forces exerted make it feel as if it weighed 12,000 pounds. At its maximum certificated gross weight, there is no problem because the aircraft is operated within its certificated maneuvering loads. But loaded to 8,000 pounds with a 60° bank or an abrupt pullup, it suddenly weighs 16,000 pounds and might not be able to perform! Even if it could, there would probably be internal stress damage that would show up on future flights
Introduction
Weight and balance in aircraft is based on the law of the lever.
This chapter discusses the application of the law of the lever
and its applications relative to locating the balance point of a beam or lever on which various weights are located or shifted. The chapter also discusses the documentation pertaining to weight and balance that is furnished by the Federal Aviation Administration (FAA) and aircraft manufacturers.
Weight and Balance TheoryChapter 2
2-2Figure 2-1. Balance lever.
B = 200
A = 100Arm B (+25") Arm A (−50")
Fulcrum
Datum− Moment + Moment
−Forces+Forces
Figure 2-2. Balance point locations.Item Weight (lb) Arm (in) Moment (lb-in)
−5,000
+5,000
0Weight AWeight B100200300−50+25
Figure 2-3. Balance lever datum located off the lever.
C = 200
A = 100
B = 100
+50+90
+110+150
CGDatumWeight and Balance Theory
Two elements are vital in the weight and balance considerations
of an aircraft.
• The total weight of the aircraft must be no greater
than the maximum weight allowed by the FAA for the make and model of the aircraft.
• The center of gravity (CG), or the point at which
all of the weight of the aircraft is considered to be concentrated, must be maintained within the allowable range for the operational weight of the aircraft.
Arm
The arm is usually measured and expressed in inches and
refers to the horizontal distance between the CG of an item
or object and the datum, a point from where all measurements are taken. Arms to the left of the datum are negative (–) and those to the right of the datum are positive (+). The datum is an imaginary vertical plane from which all horizontal distances are measured for balance purposes. The position of the reference datum varies by aircraft design and manufacturer. When the datum is located off of the lever and to the left, all of the arms are positive and computational errors are minimized. Note: When the datum is established ahead of the aircraft, for example at the aircraft nose, all of the arms are positive and computational errors are minimized.
Moment
A moment is a force that tries to cause rotation and is the
product of the arm, in inches, and the weight, in pounds.
Moments are generally expressed in pound-inches (lb-in) and may be either positive or negative.
The Law of the Lever
Weight and balance problems are based on the physical law
of the lever. This law states that a lever is balanced when the weight on one side of the fulcrum (a pivot point for the lever) multiplied by its arm is equal to the weight on the opposite side multiplied by its arm. In other words, the lever is balanced when the sum of the moments about the fulcrum is zero. This is the condition in which the positive moments (those that try to rotate the lever clockwise) are equal to the negative moments (those that try to rotate it counterclockwise). In an aircraft, the balance point is referred to as the CG.
One of the easiest ways to understand weight and balance is
to consider a lever with weights placed at various locations. The balance point or CG of the lever can be changed by either moving the weights closer or farther from the fulcrum or by increasing or decreasing the weights. The balance point or CG of a lever may be determined by using these four steps:
1. Measure the arm of each weight in inches from the
datum.2. Multiply each arm by its weight in pounds to determine
the moment in pound-inches of each weight.
3. Determine the total of all weights and of all the
moments. (Disregard the weight of the lever).
4. Divide the total moment by the total weight to
determine the balance point.
Consider these facts about the lever in Figure 2-1 . The
100-pound weight A is located 50 inches to the left of the fulcrum (the datum, in this instance), and it has a moment of
100 × –50 = –5,000 lb-in. The 200-pound weight B is located 25 inches to the right of the fulcrum, and its moment is
200 × +25 = +5,000 lb-in. In Figure 2-2, the sum of the
moments is –5,000 + 5,000 = 0, and the lever is balanced. The forces that try to rotate it clockwise have the same magnitude as those that try to rotate it counterclockwise. If either weight is moved or changed, the balance point or CG changes and the lever becomes unbalanced.
In Figure 2-3, the datum is located off the lever to the left
of weight A. Using the information provided in Figure 2-3,
2-3Figure 2-4. Finding balance point with datum located off the lever.Item Weight (lb) Arm (in) Moment CG
5,000
9,000
30,00044,000 110Weight AWeight B
Weight C1001002004005090
Figure 2-5. Locating balance point.
C = 200
A = 100
B = 100
−20−60
110+40
CGOriginal datum New datum
Figure 2-6. Proving balance point with three weights is correct.Item Weight (lb) Arm (in) Moment (lb-in)
−6,000−2,000+8,000
0Weight AWeight B
Weight C100100200−60−20+40Figure 2-7. Locating balance point with datum at C.
C = 200
A = 100
B = 100
−60−100Datum
Figure 2-8. Determining new balance point.Item Weight (lb) Arm (in) Moment CG
−10,000
−6,000
−16,000 −40Weight AWeight B
Weight C100100200400−100
−60
Figure 2-9. Locating balance point with datum left of original.
C = 200
A = 100
B = 100
−40Datum
−20−60+40determine the balance point by making a chart like the one
in Figure 2-4.
As noted in Figure 2-4 , A weighs 100 pounds and is 50 inches
from the datum; B weighs 100 pounds and is 90 inches from
the datum; C weighs 200 pounds and is 150 inches from the datum. The total of the weights is 400 pounds, and the total moment is 44,000 lb-in.
Determine the balance point by dividing the total moment
by the total weight. A balance point is equal to the CG and can be mathematically written as:
CG = total moment
total weight
To prove this is the correct balance, move the datum to a
location 110 inches to the right of the original datum and determine the arm of each weight from this new datum. [Figure 2-5] Then, make a new chart similar to the one in Figure 2-6. If the balance point is correct, the sum of the moments is zero.
The new arm of weight A is 60 inches (the difference between
110 and 50), and since this weight is to the left of the datum, its arm is negative or –60 inches. The new arm of weight B is 20 inches (110 – 90), and it is also to the left of the datum, so it is –20; the new arm of weight C is 40 inches (150 – 110). It is to the right of the datum and is therefore positive.
The lever is balanced when the sum of the moments is zero.
The location of the datum used for determining the arms of the weights is not important; it may be in various locations, but all of the measurements must be made from the same datum location.
The procedure for finding the balance point is the same
anywhere the datum is located. In Figure 2-7, the datum is
located at C. Weight A has an arm of –100 inches (negative
because it is to the left) of the datum and weight B has an arm of –60 inches from the datum. The table in Figure 2-8
is used to determine the new balance point.
To verify that this is the correct balance point, move the datum
40 inches to the left of the original datum and determine the arm of each weight from this new datum as in Figure 2-9.
2-4Figure 2-10. Proving the new balance point is correct.Item Weight (lb) Arm (in) Moment (lb-in)
−6,000
−2,000
+8,000
0Weight AWeight B
Weight C100100
200−60
−20
Figure 2-11. Locating balance point with three weights.
C = 200
B = 200
A = 100
CGDatumBefore Weight Shift
Figure 2-12. Proving the new balance point is correct.Item Weight (lb) Arm (in) Moment (lb-in)
−5,000
+10,000
+5,000Weight AWeight B
Weight C100
200−50+50Figure 2-13. Weight distribution to balance lever.
B = 200
A = 100
C = 100−50
−25
CGDatumAfter Weight Shift
Figure 2-14. Weight shift provides correct CG.Item Weight (lb) Arm (in) Moment (lb-in)
−5,000
−5,000
+10,000
0Weight AWeight B
Weight C100200200−50−25+50The new arm for weight A would be –100 + 40 = –60; for
weight B, –60 + 40 = –20; and point C, is +40. The lever is
balanced and the balance point is correct when the sum of
the moments is zero. [Figure 2-10]
Shifting the Balance Point or CG
One common weight and balance problem involves moving or shifting weight from one point to another in order to move
the balance point or CG to a desired location. This can be demonstrated by using a lever with three weights to work out the problem.
Solution by Chart
As the lever is loaded in Figure 2-11, it balances at a point
72 inches from the CG of weight A.
To shift weight B so the lever balances about its center, 50
inches from the CG of weight A, first determine the arm of weight B that produces a moment that causes the total moment of all three weights around this desired balance point to be zero. The combined moment of weights A and C around this new balance point is 5,000 lb-in, so the moment of weight B must be –5,000 lb-in for the lever to balance. [Figure 2-12]Determine the arm of weight B by dividing its moment, –5,000 lb-in, by its weight of 200 pounds. The arm is –25 inches. To balance the lever at its center, weight B must be placed so its CG is 25 inches to the left of the center of the lever. [Figure 2-13]
Figure 2-14 indicates that the shift in weight depicted in
Figure 2-13 allows the lever to balance as the sum of the
moments is zero.
Basic Weight and Balance Equation
The following formulas can be used to determine the distance
weight must be shifted to obtain a desired change in the CG location. The equation can also be rearranged to fi d the amount of weight required to be shifted to move the CG to a desired location, to find the distance the CG is moved when a specified amount of weight is shifted, or to find the total weight that would allow shifting a specified amount of weight to move the CG a given distance.
Weight to be shifted =
Δ CG
Total weight Distance weight is shifted
Total weight = Weight shifted × Distance weight is shifted
Δ CG
Weight shifted = Total weight shifted × Δ CG
Distance weight is shifted
Δ CG = Weight shifted × Distance weight is shifted
Total weight
Distance weight is shifted = Total weight × Δ CG
Weight shifted
2-5Figure 2-14. Center of gravity expressed as percent mean
aerodynamic chord.
MAC MAC
30% MAC15% MAC Datum
Quarter chord
Half
semi-spanSolution by Formula
The problem in Figure 2-11 can be solved by using variations
of this basic equation. First, rearrange the formula to
determine the distance weight B must be shifted:
Distance weight B is shifted = Total weight × Δ CG
Weight shifted
= 500 × –22
= –55 inches
The CG of the lever in Figure 2-11 was 72 inches from the
datum. This CG can be shifted to the center of the lever as in
Figure 2-13 by moving weight B. If the 200-pound weight B
is moved 55 inches to the left, the CG shifts from +72 inches to +50 inches, a distance of 22 inches.
When the distance the weight is to be shifted is known,
the amount of weight to be shifted to move the CG to any location can be determined by another arrangement of the basic equation. Use the following arrangement of the formula to determine the amount of weight that has to be shifted from station 8 to station +25, to move the CG from station +72 to station +50.
Weight shifted =
Total weight × Δ CG
Distance weight is shifted
= 500 × 22
= 200 inchesIf the 200-pound weight B is shifted from station +80 to
station +25, the CG moves from station +72 to station +50.
A third arrangement of this basic equation is used to
determine the amount the CG is shifted when a given amount of weight is moved for a specified distance (as it was done in Figure 2-11). The following formula is used to determine
the amount the CG is shifted when 200-pound weight B is moved from +80 to +25.
Δ CG = Weight shifted × Distance it is shifted
Total weight
= 200 × 55
= 22 inches Moving weight B from +80 to +25 moves the CG 22 inches from its original location at +72 to its new location at +50 as seen in Figure 2-13.
To complete the calculations, return to the original formula
and enter the appropriate numbers.
Weight to be shifted =
Δ CG
Total weight Distance weight is shifted
200 = 22
.4 = .4
The equation is balanced.
Mean Aerodynamic Chord
The CG point affects the stability of the aircraft. To ensure
the aircraft is safe to fly, the CG must fall within specifiedlimits established by the manufacturer.
On some aircraft, the CG is expressed as a percentage of the
length of the mean aerodynamic chord (MAC) or “percent MAC.” [Figure 2-14] In order to make such a calculation,
the position of the leading edge of the MAC must be known ahead of time.
CG limits are specified forward and aft and/or lateral (left and
right) limits within which the aircraft’s CG must be located during flight. The area between the limits is called the CG range of the aircraft.
2-6The position of the fore and aft CG limits is measured as a
percentage of MAC from the MAC leading edge. Usually for a single or two-seat aircraft, the most forward position would be forward of 30–35 percent MAC. Thus, the allowable CG range in a light aircraft should not exceed 20 percent MAC.
Note: For a rectangular width of constant airfoil section
dimensions, MAC is just the chord. For a symmetrically-tapered wing, it is the average of the root chord and the tip chord.
FAA-Furnished Weight and Balance
Information
The information discussed to this point can be readily applied
to any aircraft weight and balance problem. To apply the techniques, certain elements of information are required. This information is obtained from both FAA documents and manufacturer provided data.
Before an aircraft CG can be computed, certain information
must be known. This information, furnished by the FAA for every certificated aircraft in the Type Certificate Data
Sheets (TCDS) or Aircraft Specifications, can be accessed at www.faa.gov. When the design of an aircraft is approved by the FAA, an Approved Type Certificate and TCDS are issued. The TCDS includes all of the pertinent specification for the aircraft; at each annual or 100-hour inspection, it is the responsibility of the inspecting mechanic or repairman to ensure that the aircraft adheres to them. A note about the TCDS: aircraft certifi ated before January 1, 1958, were issued Aircraft Specifica ions under the Civil Air Regulations
(CARs), but when the Civil Aeronautical Administration
(CAA) was replaced by the FAA, Aircraft Specification were replaced by the TCDS.
The weight and balance information on a TCDS includes CG
range, empty weight CG range (EWCG), maximum weights,
number of seats, maximum baggage, fuel capacity, oil capacity, and datum location. Data pertinent to an individual model is located in its respective section of the TCDS. Use the TCDS excerpts in Figure 2-15 to verify the following for
a Cirrus Design Corporation SR 20 normal category:
CG Range
S/N 1005 through 1147:
Forward Limits: 138.7 inches at 2,110 lb with a straight line
taper to 141.0 in at 2,694 lb and 143.0 in at 2,900 lb
Aft Limits: 144.6 in at 2,110 lb, with straight line taper to
147.4 in at 2,570 lb, and to 147.9 in at 2,745 lb, and 148.2 in at 2,900 lbS/N 1148 through 1877, 1879 through 1885, and S/N 1005 through 1147 if Cirrus Service Bulletin SB 20-01-00 is complied with:Forward Limits: 138.7 in at 2,110 lb with a straight line taper to 141.0 in at 2,694 lb and 144.1 in at 3,000 lb
Aft Limits: 144.6 in at 2,110 lb, with straight line taper to
147.4 in at 2,570 lb, and to 148.1 in at 2,900 lb, and 148.0 in at 3,000 lb
S/N 1878, 1886 and Subsequent:
Forward Limits: 137.8 in at 2,100 lb with a straight line taper
to 139.1 in at 2,700 lb, and to 140.7 in at 3,050 lb
Aft Limits: 148.1 in at 2,100 lb, with straight line to 148.1
in at 3,050 lb
Empty Weight CG Range (EWCG)
When all of the seats and baggage compartments are located
close together, it is not possible (as long as the EWCG is located within the EWCG range) to legally load the aircraft so that its operational CG falls outside this allowable range. If the seats and baggage areas extend over a wide range, the EWCG range is listed as “None.”
Maximum Weights
The maximum allowable takeoff and landing weights and
the maximum allowable ramp weight are given. This basic information may be altered by a note. Notes are found in data pertinent to all models. An example would be Note 6 at the end of Figure 2-15.
Number of Seats
The number of seats and their arms are given in such terms
as: 4 (2 at 143.5 aft of datum, 2 at 180 aft of datum).
Maximum Baggage
Maximum baggage for this model is 130 pounds at 208
inches.
Fuel Capacity
This important information is given in such terms as: 60.5
gal at 153.75 in. Usable: 56 gal (See Note 1). Notes can be found in data pertinent to all models.
Oil Capacity (Wet Sump)
The quantity of the full oil supply and its arm are given: 8
quarts at 76.2 in.
2-7Figure 2-15. Sample excerpt from TCDS A00009CH.Page No. 1 2 3 4 5 6 7
Rev. No. 11 12 12 14 14 16 16 DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
A00009CH
Revision 16
Cirrus Design Corporation
SR20
SR22
April 22, 2009
TYPE CERTIFICATE DATA SHEET NO. A00009CH
This data sheet, which is part of Type Certificate No. A 00009CH, prescribes conditions and limitations under which the product
for the which type certificate was issued meets the airwor thiness requirements of the Federal Aviation Regulations.
Type Certificate Holder: Cirrus Design Corporation
4515 Taylor Circle
Duluth, MN 55811
I - Model SR20, (Normal Category), Approved October 23, 1998
Engine Teledyne Continental IO-360-ES, Ty pe Certificate Data Sheet (TCDS) E1CE
Fuel 100/100LL minimum grade aviation gasoline
Engine Limits Maximum Take-off 2700 RPM (200 hp)
Maximum Continuous Power 2700 RPM (200 hp)
Propeller and Propeller limits 1. Hartzell Prope ller Inc. P/N BHC-J2YF-1BF/F7694
TCDS P37EA
Maximum Diameter: 76 inches
Minimum Diameter: 73 inches
Number of Blades: 2
Low Pitch: 14.6°+/-0.5°
High Pitch: 35.0°+/-1.0°
Not to be operated above 24 inches of manifold pressure between 1900 and 2200 RPM.
Spinner: Hartzell P/N A-2295(P) NOTE: Spinner may be painted or polished.
2. Hartzell Propeller Inc. P/N PHC-J3YF-1MF/F7392-1
TCDS P36EA
Maximum Diameter: 74 inches
Minimum Diameter: 72 inches
Number of Blades: 3
Low Pitch: 14.1°+/-0.5°
High Pitch: 35.0°+/-1.0°
No operating limitations to 2800 RPM
Spinner: Hartzell P/N A-2295-1P
3. Hartzell Propeller Inc. P/N PHC-J3YF-1RF/F7392-1
TCDS P36EA
Maximum Diameter: 74 inches
Minimum Diameter: 72 inches
Number of Blades: 3
Low Pitch: 13.9°+/-0.5°
High Pitch: 35.0°+/-1.0°
No operating limitations to 2800 RPM
Spinner: Hartzell P/N A-2295-1(P) NOTE: Spinner may be painted or polished.
2-8Figure 2-15. Sample excerpt from TCDS A00009CH (continued).A00009CH -2-
Airspeed Limits S/N 1005 thru 1147:
Vne Never Exceed Speed 200 KIAS
Vno Maximum Structural Cruising Speed 165 KIAS
Vo (2900 lbs) Operating Maneuvering Speed 135 KIAS
Vo (2600 lbs) Operating Maneuvering Speed 126 KIAS
Vo (2200 lbs) Operating Maneuvering Speed 116 KIAS
Vfe Maximum Flap Extension Speed 100 KIAS
Vpd Maximum Parachute Deployment Speed 135 KIAS
S/N 1148 thru 1877, 1879 thru 1885, and S/N 1005 thru 1147 if Cirrus Service Bulletin SB 20-01-
00 is complied with:
Vne Never Exceed Speed 200 KIAS
Vno Maximum Structural Cruising Speed 165 KIAS
Vo (3000 lbs) Operating Maneuvering Speed 131 KIAS
Vo (2600 lbs) Operating Maneuvering Speed 122 KIAS
Vo (2300 lbs) Operating Maneuvering Speed 114 KIAS
Vfe Maximum Flap Extension Speed 100 KIAS
Vpd Maximum Parachute Deployment Speed 135 KIAS
S/N 1878, 1886 and subsequent:
Vne Never Exceed Speed 200 KIAS
Vno Maximum Structural Cruising Speed 163 KIAS
Vo (3050 lbs) Operating Maneuvering Speed 130 KIAS
Vfe Maximum Flap Extension Speed 104 KIAS
Vpd Maximum Parachute Deployment Speed 133 KIAS
C.G. Range S/N 1005 thru 1147:
Forward Limits: 138.7 inches at 2110 lbs with a straight line taper to 141.0 inches at 2694 lbs, and
143.0 inches at 2900 lbs.
Aft Limits: 144.6 inches at 2110 lbs, with straight line taper to 147.4 inches at 2570 lbs, and to 147.9 inches at 2745 lbs, and 148.2 inches at 2900 lbs.
S/N 1148 thru 1877, 1879 thru 1885, and S/N 1005 thru 1147 if Cirrus Service Bulletin SB 20-01-
00 is complied with:
Forward Limits: 138.7 inches at 2110 lbs with a straight line taper to 141.0 inches at 2694 lbs, and 144.1 inches at 3000 lbs.
Aft Limits: 144.6 inches at 2110 lbs, with straight line taper to 147.4 inches at 2570 lbs, and to 148.1 inches at 2900 lbs, and 148.0 inches at 3000 lbs.
S/N 1878, 1886 and subsequent:
Forward Limits: 137.8 inches at 2100 lbs with a straight line taper to 139.1 inches at 2700 lbs, and to 140.7 inches at 3050 lbs
Aft Limits: 148.1 inches at 2100 lbs, with straight line to 148.1 inches at 3050 lbs.
Empty Weight C.G. Range None
Maximum Weight S/N 1005 thru 1147:
Takeoff and Landing: 2900 lbs.
S/N 1148 thru 1877, 1879 thru 1885, and S/N 1005 thru 1147 if Cirrus Service Bulletin SB 20-01-
00 is complied with:
Takeoff: 3000 lbs.
Landing: 2900 lbs.
Zero Fuel: 2900 lbs.
S/N 1878, 1886 and subsequent:
Takeoff and Landing: 3050 lbs.
2-9Figure 2-15. Sample excerpt from TCDS A00009CH (continued).
Figure 2-15. Sample excerpt from TCDS A00009CH (continued). -3- A00009CH
Minimum Crew One (1) Pilot
Number of Seats 4 (2 at 143.5 inches aft of datum, 2 at 180 inches aft of datum) Maximum Baggage 130 Lbs. at 208 inches Fuel Capacity Total: S/N 1005 thru 1877, 1879 thru 1885
60.5 gal at 153.75 inches
Usable: 56 gal (See Note 1)
S/N 1878, 1886 and subsequent:
58.5 gal at 154.9 inches
Usable: 56 gal (See Note 1)
Oil Capacity 8 quarts at 76.2 inches
Maximum Operating Altitude With a portable oxygen system, the aircraft is limited to 17,500 ft MSL.
Oxygen must be provided as required by the operating rules. Only portable oxygen systems listed in the FAA Approved Airplane Flight Manual, document number 11934-002, or later FAA approved revisions, are allowed.
Control Surface Movements Wing Flaps: Up 0°± 0.5° Down 50% 16°± 0.5° Down 100% 32°± 0.5°
Aileron: Up 12.5° ± 1.0° Down 12.5° ±1.0°
Elevator: Up 25.0° +0°/-1.0° Down 15° ± 1.0°
Elevator Trim: Up 17.0° Minimum Down 10.5° ± 1.0°
Rudder: Right 20.0° ± 1.0° Left 20.0° ± 1.0°
Additional Limitations: Airframe life limit: 12,000 flight hours
Design Data: The airplane shall be manufactured in accordance with the latest FAA approved revision of
“Master Drawing List”, Document No. 13750, or other FAA approved data. NOTE: Document
No. 12609 is the predecessor document to Document No. 13750.
Serial Nos. Eligible 1005 and on
II - Model SR22, Normal Category, Approved November 30, 2000
Engine Teledyne Continental IO-550-N, Type Certificate Data Sheet E3SO
Engine Limits Maximum Take-off 2700 RPM (310 hp)
Maximum Continuous Power 2700 RPM (310 hp)
Propeller and Propeller limits 1. Hartzell Propeller Inc. P/N PHC-J3YF-1RF/F7694 or F7694B TCDS P36EA Hartzell
Maximum Diameter: 78 inches
Minimum Diameter: 76 inches
Number of Blades: 3
Low Pitch: 14.1°+/-0.5°
High Pitch: 35.0°+/-1.0°
No operating limitations to 2700 RPM
Spinner: Hartzell P/N A-2295-1(P) NOTE: Spinner may be painted or polished.
2. McCauley Propeller Systems P/N D3A34C443/78CYA-0
TCDS P47GL McCauley
Maximum Diameter: 78 inches
Minimum Diameter: 76 inches
Number of Blades: 3 -5- A00009CH
Minimum Crew One (1) Pilot
Number of Seats 4 (2 at 143.5 inches aft of datum, 2 at 180 inches aft of datum) Maximum Baggage 130 Lbs. at 208 inches Fuel Capacity Total: S/N 0002 thru 2333, 2335 thru 2419, and 2421 thru 2437
84 gallon at 154.9 inches
Usable: 81 gallon (See Note 1)
S/N 2334, 2420, 2438 and subsequent
94.5 gallon at 154.9 inches
Usable: 92.0 gallon (See Note 1)
or
58.5 gal at 154.9 inches
Usable: 56 gal (See Note 1)
Oil Capacity 8 quarts at 77.1 inches
Maximum Operating
Altitude With a portable oxygen system, the aircraft is limited to 17,500 ft MSL.
Oxygen must be provided as required by the operating rules. Only portable oxygen systems listed in the FAA Approved Airplane Flight Manual, document number 13772-001, or later FAA approved revisions, are allowed.
Control Surface Movements Wing Flaps: Up 0°±0.5° Down 50% 16° ± 0.5° Down 100% 32° ±0.5°
Aileron: Up 12.5° ± 1.0° Down 12.5° ± 1.0°
Aileron Trim: Up 6 ± 1.0° Down 6 ± 1.0°
Elevator: Up 25.0° +0°/-1.0° Down 15° ± 1.0°
Elevator Trim: Up 17.0° Minimum Down 10.5° ± 1.0°
Rudder: Right 20.0° ± 1.0° Left 20.0° ± 1.0°
Additional Limitations: Airframe life limit: 12,000 flight hours
Design Data: The airplane shall be manufactured in accordance with the latest FAA approved revision of
“Master Drawing List”, Document No . 13750, or other FAA approved data.
Serial Nos. Eligible 0001 and on.
Data Pertinent to All Models
Reference Datum 100 inches in front of the forward face of firewall bulkhead
Leveling Means Door sill and leve ling points as defined in AFM
Certification Basis Model SR20 : 14 CFR Part 23 of the Federal Aviation Regulations effective February 1, 1965, as
amended by 23-1 through 23-47, except as follows:
14 CFR 23.573, 23.575, 23.611, 23.657, 23.673 through Amendment 23-48;
14 CFR 23.783, 23.785, 23.867, 23.1303, 23.1307, 23.1309, 23.1311, 23.1321, 23.1323,
23.1329, 23,1361, 23.1383, 23.1401, 23.1431, 23.1435 through Amendment 23-49;
14 CFR 23.3, 23.25, 23.143, 23.145, 23.155, 23.1325, 23.1521, 23.1543, 23.1555, 23.1559, 23.1567, 23.1583, 23.1585, 23.1589 through Amendment 23-50;
14 CFR 23.777, 23.779, 23.901, 23.907, 23.955, 23.959, 23.963, 23.965, 23.973, 23.975, 23.1041, 23.1091, 23.1093, 23.1107, 23.1121, 23.1141, 23.1143, 23.1181, 23.1191, 23.1337
through Amendment 23-51;
14 CFR 23.1305 through Amendment 23-52
Noise
: 14 CFR Part 36 dated December 1, 1969 as amended by 36-1 through 36-21.
2-10Figure 2-16. Weight and balance report.Item C.G. Arm (in) Moment (lb-in/1,000)
Standard empty weight
Optional equipmentSpecial installationPaintUnusable fuelBasic empty weight 1,876.0 1.2 6.2 — 30.0 1,913.4 67,798.6 16.7 257.3 — 1,380.0 69,452.6 36.1 13.9 41.5 — 46.0
Aircraft Serial No. 18259080 FAA Registration No. N42565 Date: 4-22-09
Weight (lb) × Figure 2-15. Sample excerpt from TCDS A00009CH (continued). -7- A00009CH
Special Conditions 23-ACE-88 for ballistic parachute, for models SR20, SR22.
23-134-SC for protection of systems for High Inte nsity Radiated Fields (H IRF), for models SR20,
SR22.
23-163-SC for inflatable restraint system. Addition to the certification basis model SR20 effective S/N 1541 and subsequent; model SR22 S/N 1500, 1520 and subsequent.
Exemptions Exemption No. 9849 to regulation 23.1419(a) for Flight Into Known Icing operations only on
model SR22 (Effective S/N 3003, 3310, 3326, 3403 and subsequent). Exemption allows for a higher stall speed than that required by 23.49(c) & (d) when operating in icing conditions.
Production Basis Production Certificate 338CE issued June 12, 2000
Equipment The basic required equipmen t as prescribed in the applicab le airworthiness regulations (See
Certification Basis) must be installe d in the airplane for certification.
In addition to the above required equipment, the following equipment are also required:
• The latest FAA approved Revision of the “PILOT’S OPERATING HANDBOOK AND FAA
APPROVED AIRPLANE FLIGHT MANUAL for the CIRRUS DESIGN SR20”, Document No.
11934-001 for aircraft serials 1005 through 1147 with 2900 pound TOGW, Document No. 11934-
002 for aircraft serials 1005 through 1147 with 3000 pound TOGW and for aircraft serials 1148
through 1267, Document No. 11934-003 for aircraft serials 1268 and subsequent, or Document No. 11934-004 for aircraft serials 2016 and subsequent.
• The latest FAA approved Revision of the “PILOT’S OPERATING HANDBOOK AND FAA
APPROVED AIRPLANE FLIGHT MANUAL for the CIRRUS DESIGN SR22”, Document No.
13772-001 for aircraft serials 0002 a nd subsequent, or Document No . 13772-002 for aircraft serials
2979, 2992, 3002 and subsequent.
Note 1. A current weight and balance report including list of equipment included in the certificated empty weight, and
loading instructions when necessary must be provided for each aircraft at the time of original certification. The
certificated empty weight and loading corresponding center of gravity location must include unusable fuel of 27 lb. at (+153.8 inches) for model SR20 S/N 1005 thru 1877, 1879 thru 1885; unusable fuel of 18 lb at (+154.9 inches) for model SR22 S/N 0002 thru 2333, 2335 thru 2419, and 2421 thru 2437; and unusable fuel of 15 lb at
(+154.9 inches) for models SR22 S/N 2334, 2420, 2438 and subsequent, and SR20 S/N 1878, 1886 and subsequent.
Note 2. All placards specified in the latest FAA approved revisions of the "PILOT'S OPERATING HANDBOOK AND
FAA APPROVED AIRPLANE FLIGHT MANUAL FOR THE CIRRUS SR 20", document numbers 11934-001,
11934-002, 11934-003 or 11934-004 and the latest FAA appr oved revisions of the "PILOT'S OPERATING
HANDBOOK AND FAA APPROVED AIRPL ANE FLIGHT MANUAL FOR THE CIRRUS SR22" document
numbers 13772-001 or 13772-002 must be displayed in the airplane in the appropriate locations.
Note 3. FAA approved Airworthiness Lim itations are included in Section 4 of the Airplane Maintenance Manual (AMM)
Document No. 12137-001 for model SR20, and 13773-001 for model SR22.
Note 4. Exterior colors are limited to those specified in the latest FAA accepted revision of the Airplane Maintenance
Manual (AMM) Document No. 12137-001 for model SR20, and 13773-001 for model SR22.
Note 5. Major structural repairs must be accomplished in accordance with FAA approved Cirrus
Design repair methods or other methods approved by the FAA.
Note 6. For Model SR22 S/N 0002 thru 2333, 2335 thru 2419, and 2421 thru 2437 a maximum landing weight exists
along the line between 141.4 inches at 3210 lbs and 142.7 inches at 3400 lbs.
-- END --
Data Pertinent to all Models
The location of the datum is specified and is described, for
example, as: 100 inches in front of the forward face of the firewall bulkhead.
Manufacturer-Furnished Information
When an aircraft is initially certificated, its empty weight and EWCG are determined and recorded in the weight and balance record, such as the one in Figure 2-16. Notice in this figur
that the moment is expressed as “Moment (lb-in/1,000).” This is a moment index, which means that the moment, a very large number, has been divided by 1,000 to make it more manageable. Chapter 4, Light Sport Aircraft—Weight and Balance Control, discusses moment indices in more detail.
The aircraft is furnished with an equipment list, specifies
all the required equipment and all equipment approved for installation in the aircraft. The weight and arm of all installed equipment are included on the list and checked prior to the aircraft leaving the factory.
When an aircraft mechanic or repairman adds or removes
any item on the equipment list, he or she must change the weight and balance record to indicate the new empty weight and EWCG, and the equipment list is revised to show which equipment is actually installed. Figure 2-17 is from a
comprehensive equipment list that includes all of the items of equipment approved for this particular model of aircraft. The pilot’s operating handbook (POH) for each individual
aircraft includes an aircraft-s pecifi c equipment list of the
items from this master list. When any item is added to or removed from the aircraft, its weight and arm are determined in the equipment list and used to update the weight and balance record. The POH and airplane flight manual (AFM) also contain CG moment envelopes and loading graphs. Examples of the use of these helpful graphs are given in Chapter 5, Single-Engine Aircraft Weight and Balance Computations.
In addition to the weight and balance report and equipment
list, the manufacturer also provides a CG range chart. The
CG range can be found in text form in the TCDS. The CG range chart is furnished in the POH.
2-11Figure 2-17. Excerpt from a typical comprehensive equipment list.
2-12Figure 2-17. Excerpt from a typical comprehensive equipment list (continued).
Introduction
Chapter 2, Weight and Balance Theory, explained the theory
of weight and balance and gave examples of the way the center of gravity (CG) could be found for a lever loaded with several weights. In this chapter, the practical aspects of weighing an airplane and locating its CG are discussed. Formulas are introduced that allow the CG location to be measured in inches from various datum locations and in percentage of the mean aerodynamic chord (MAC).
Weighing the Aircraft and
Determining the Empty Weight
Center of GravityChapter 3
3-2Figure 3-1. Platform scales.
Requirements
Regulations do not require periodic weighing of privately
owned and operated aircraft. Such aircraft are usually weighed when originally certificated or after major alterations that can affect the weight and balance. The primary purpose of aircraft weight and balance control is safety. Manufacturers
conduct extensive flight tests to establish loading limits for their aircraft because limit information is critical for safe flight. A secondary purpose is to aid efficiency during flight. Overloading of the aircraft is not the only concern; the distribution of the weight is important also. The aircraft has CG limits, and any loading that places the CG outside the established limits seriously impairs controllability of the aircraft.
Weight and balance is of such vital importance that each
Federal Aviation Administration (FAA) certificated mechanic or repairman maintaining an aircraft must be fully aware of his or her responsibility to provide the pilot with current and accurate information for the actual weight of the aircraft and the location of the CG. The pilot in command
(PIC) is responsible for knowing the weight of the load, CG, maximum allowable weight, and CG limits of the aircraft. The weight and balance report must include an equipment list showing weights and moment arms of all required and optional items of equipment included in the certificate empty weight.
Weight and balance records used in accounting for and
correcting the CG location are reliable for only limited periods of time. For this reason, periodic aircraft weighing is desirable. An aircraft should be reweighed and a new weight and balance record should be started after the aircraft has undergone extensive repair or major alteration, when the pilot reports unsatisfactory flight characteristics (e.g., nose or tail heaviness), and when recorded weight and balance data are suspected to be in error.
Repairs and alterations are major sources of weight change.
The airframe and powerplant (A&P) FAA-certificated mechanic or repairman who is responsible for making any repair or alteration must:
1. Establish by computation that the authorized weight
and CG limits as shown in the type certificate data sheet (TCDS) and aircraft specifications are not exceeded, and
2. Record the new empty weight center of gravity
(EWCG) data in the current approved aircraft flightmanual or issued operating limitations.
When an aircraft has undergone extensive repair or major
alteration, it should be reweighed and a new weight and balance record started. The A&P FAA-certificated mechanic or repairman responsible for the work must provide the pilot with current and accurate aircraft weight information and location of the EWCG.
Equipment for Weighing
Weighing aircraft with accurately calibrated scales is the only sure method of obtaining an accurate empty weight and CG location. The two basic types of scales used to weigh aircraft are platform and load cell.
Platform scales [Figure 3-1] or ramp wheel scales
[Figure 3-2] (usually a form or modified version of the
platform scale) are low profi e, easy to handle, safe, and
reliable. Tow or push the aircraft wheels or skids onto the scale pad at ground level. With one scale per wheel, each device should be capable of measuring up to at least 60,000 pounds since the weight on each wheel rarely exceeds this figure
Load cell scales [Figure 3-3] are also a reliable means to
weigh aircraft and are typically cheaper than the platform type.Using load cell scales allows for the aircraft to be set up and weighed in its level flight attitude. With this method, the aircraft is placed on jacks with electronic load cells placed between the jack and the jack pad on the aircraft. The aircraft is raised on the jacks until the wheels or skids are off the floor and the aircraft is in a level flight attitude. The weight measured by each load cell is indicated on the control panel. Jacking an aircraft off the ground from all load points can be an inconvenience, as well as a safety risk, which some operators would rather avoid by opting for more expensive—but simpler to use—platform equipment. In addition, weighing with platform scales typically takes only one-third of the time needed to weigh with load cells.
3-3Figure 3-2. Ramp scales.
Figure 3-3. Load cell scales.
All scales for aviation use, manual or electronic, must be
protected when stored or shipped, and they must be checked
periodically for accuracy. The maximum recognized period between calibration checks is 12 months; however, this period may be reduced by an airworthiness authority dependent on the conditions of use. Scales in daily use may require a shorter
interval and/or testing to determine the continued accuracy of the unit. Scales should be returned to the manufacturer for proper calibration and testing.
Preparation for Weighing
In general, weight procedures may vary with the aircraft
and types of weight equipment employed. The weighing procedure contained in the manufacturer’s maintenance manual should be followed for each particular aircraft. The major considerations in preparing an aircraft for weighing are described in the following paragraphs.
Scale Preparation
Mechanical and electronic scales shall be inspected prior to
use and set to zero. This is done by adding and removing a weight, then rechecking for zero. This process should be repeated until a steady zero setting is obtained. The scales should be located in the same environment in which they
3-4Figure 3-4. Standard fuels and weights with temperatures of 32 °F
and 59 °F.Weighing Point
AVGAS (Aviation Gasoline)
JET A & A-1
Water
Oil6.14
6.758.357.506.016.688.337.43Pounds per U.S. Gallon
32 °F 59 °Fare to be used and allowed to come up to temperature at
least 2 hours prior to use. Scales should not be used in temperature extremes below 40 °F or above 100 °F unless the scale is specifically designed for use in those temperatures. Electronic scales are very sensitive and, if subjected to freezing temperatures, the liquid displays may be damaged beyond use.
Weigh Clean Aircraft Inside Hangar
The aircraft should be weighed inside a hangar where wind
cannot blow over the surface and cause fluctuating or false scale readings. The aircraft should be clean inside and out, with special attention paid to the bilge area to ensure that no water or debris is trapped there. The outside of the aircraft should be as free as possible of all mud and dirt.
Equipment List
All of the required equipment must be properly installed, and
there should be no equipment installed that is not included in the equipment list. If such equipment is installed, the weight and balance record must be corrected to indicate it.
Ballast
All required permanent ballasts must be properly secured in
place. All temporary ballasts must be removed.
Standard Weights
Standard weights are established weights for numerous items
involved in weight and balance computations. These weights should not be used if actual weights are available. Some of the standard weights are listed in Figure 3-4.
Note the difference in weight as temperatures change.
Although this change is a very small amount per gallon, it could end up in a significant total weight gain when dealing with large quantities of fluids, such as those found in commercial aircraft.
Draining the Fuel
Drain fuel from the tanks in the manner specified by the
aircraft manufacturer. If there are no specific instructions, drain the fuel until the fuel quantity gauges read empty when the aircraft is in level-flight attitude. Any fuel remaining in the system is considered residual or unusable fuel and is part of the aircraft empty weight.
The amount of residual fuel and its arm are normally found
in Note 1 in the section of the Type Certificate Data Sheets (TCDS), “Data pertaining to all Models.” For additional fuel capacity information, see Chapter 2, Weight and Balance Theory.
If it is not feasible to drain the fuel, the tanks can be topped
off to be sure of the quantity they contain and the aircraft weighed with full fuel. After weighing is complete, the weight of the fuel and its moment are subtracted from those of the aircraft as weighed. To correct the empty weight for the residual fuel, add its weight and moment.
When computing the weight of the fuel (e.g., a tank full of
jet fuel), measure its specific gravity (sg) with a hydrometer and multiply it by 8.345 (the nominal weight of 1 gallon of pure water whose sg is 1.0). If the ambient temperature is high and the jet fuel in the tank is hot enough for its specificgravity to reach 0.81 rather than its nominal sg of 0.82, the fuel actually weighs 6.76 pounds per gallon rather than its normal weight of 6.84 pounds per gallon.
Oil
The empty weight for aircraft certificated under the Civilian
Air Regulations (CAR) part 3 does not include the engine
lubricating oil. The oil must either be drained before the aircraft is weighed, or its weight must be subtracted from the scale readings to determine the empty weight. To weigh an aircraft that does not include the engine lubricating oil as part of the empty weight, place it in level flight attitude, then open the drain valves and allow the oil to drain out. Any remaining is undrainable oil and is part of the empty weight. Aircraft certificated under Title 14 of the Code of Federal Regulations (14 CFR) parts 23 and 25 include full oil as part of the empty weight. If it is impractical to drain the oil, the reservoir can be filled to the specified level and the weight of the oil computed at 7.5 pounds per gallon. Then, its weight and moment are subtracted from the weight and moment of the aircraft as weighed. The amount and arm of the undrainable oil are found in Note 1 of the TCDS, and this must be added to the empty weight.
Other Fluids
The hydraulic fluid reservoir and all other reservoirs
containing fluids required for normal operation of the aircraft should be full. Fluids not considered to be part of the empty weight of the aircraft are potable (drinkable) water, lavatory precharge water, and water for injection into the engines.
3-5Figure 3-5. Locating the CG of an airplane relative to the datum.Weighing point Net weight (lb) TARE weight (lb) Scale reading (lb) Arm (in) Moment (lb-in) CG
−32.0
32.8Right side
Left side
Nose
Total1616
2,00638,18038,456
−10,880
65,756846852348Configuration of the Aircraf
Consult the aircraft service manual regarding position of
the landing gear shock struts and the control surfaces for
weighing. When weighing a helicopter, the main rotor must be in its correct position.
Jacking the Aircraft
Aircraft are often weighed by rolling them onto ramps in
which load cells are embedded. This eliminates the problems associated with jacking the aircraft off the ground. However, many aircraft are weighed by jacking the aircraft up and then lowering them onto scales or load cells.
Extra care must be used when raising an aircraft on jacks for
weighing. If the aircraft has spring steel landing gear and it is jacked at the wheel, the landing gear will slide inward as the weight is taken off of the tire, and care must be taken to prevent the jack from tipping over.
For some aircraft, stress panels or plates must be installed before
the aircraft is raised with wing jacks to distribute the weight
over the jack pad. Be sure to follow the recommendations of the aircraft manufacturer in detail anytime an aircraft is jacked. When using two wing jacks, take special care to raise them simultaneously, keeping the aircraft so it does not slip off the jacks. As the jacks are raised, keep the safety collars screwed down against the jack cylinder to prevent the aircraft from tilting if one of the jacks should lose hydraulic pressure.
Leveling the Aircraft
When an aircraft is weighed, it must be in its level fligh
attitude so that all of the components are at their correct distance from the datum. This attitude is determined by information in the TCDS. Some aircraft require a plumb line to be dropped from a specified location so that the point of the weight (the bob) hangs directly above an identifiable point. Others specify that a spirit level be placed across two leveling lugs, often special screws on the outside of the fuselage. Other aircraft call for a spirit level to be placed on the upper door sill.
Lateral level is not specified for all light aircraft, but
provisions are normally made on helicopters for determining both longitudinal and lateral level. This may be done by built-in leveling indicators, or by a plumb bob that shows the conditions of both longitudinal and lateral level.The actual adjustments to level the aircraft using load cells are made with the jacks. When weighing from the wheels, leveling is normally done by adjusting the air pressure in the nosewheel shock strut.
Safety Considerations
Special precautions must be taken when raising an aircraft
on jacks.
1. Stress plates must be installed under the jack pads if the manufacturer specifies them
2. If anyone is required to be in the aircraft while it is
being jacked, there must be no movement.
3. The jacks must be straight under the jack pads before
beginning to raise the aircraft.
4. All jacks must be raised simultaneously and the safety
devices are against the jack cylinder to prevent the aircraft tipping if any jack should lose pressure. Not all jacks have screw down collars, some use drop pins or friction locks.
Determining the CG
When the aircraft is in its level flight attitude, drop a plumb line from the datum and make a mark on the hangar floorbelow the tip of the bob. Draw a chalk line through this point parallel to the longitudinal axis of the aircraft.
Then, draw lateral lines between the actual weighing
points for the main wheels, and make a mark along the longitudinal line at the weighing point for the nosewheel or the tailwheel. These lines and marks on the floor allow accurate measurements between the datum and the weighting points to determine their arms.
Determine the CG by adding the weight and moment of
each weighing point to determine the total weight and total moment. Then, divide the total moment by the total weight to determine the CG relative to the datum. As an example of locating the CG with respect to the datum, which in this case is the firewall, consider the tricycle landing gear airplane as detailed in the Figure 3-5 table and illustrated in Figure 3-6.
When the airplane is on the scales with the parking brakes
3-6Figure 3-9. Determining the CG with datum forward of an airplane
with nosewheel landing gear.CG F × L
W= D −
= 128 −
114.8=( )
340 × 78
2,006( )Figure 3-8. The datum is 100 inches forward of the wing root
leading edge.
D = 128.0
114.8Datum
L = 78.0
Figure 3-10. The datum is aft of the main wheels at the wing
trailing edge.
D = 75
88.2Datum
L = 78.0Figure 3-7. Determining the CG.CG Total moment
Total weight=
65,756
2,006=
32.8 inches behind the datum=Figure 3-6. The datum is located at the firewall.
32.8Datum
off, place chocks around the wheels to keep the airplane
from rolling. Subtract the weight of the chocks, called tare weight, from the scale reading to determine the net weight at each weighing point. Multiply each net weight by its arm to determine its moment, and then determine the total weight and total moment. The CG is determined by dividing the total
moment by the total weight. [Figure 3-7]
The airplane illustrated in Figures 3-5 and 3-6 has a net
weight of 2,006 pounds, and its CG is 32.8 inches behind
the datum.
EWCG Formulas
A chart such as the one in Figure 3-5 helps the pilot visualize
the weights, arms, and moments when solving an EWCG problem, but it is quicker to determine the EWCG by using formulas and an electronic calculator. The use of a calculator for solving these problems is described in Chapter 8, Use of Computers in Weight and Balance Computations.
There are four possible conditions and their formulas that
relate the location of CG to the datum. Notice that the formula for each condition first determines the moment of the nosewheel or tailwheel and then divides it by the total weight of the airplane. The arm thus determined is then added to or subtracted from the distance between the main wheels and the datum, distance D.
Datum Forward of the Airplane— Nosewheel
Landing Gear
The datum of the airplane in Figure 3-8 is 100 inches forward
of the leading edge of the wing root or 128 inches forward of the main-wheel weighing points. This is distance (D). The
weight of the nosewheel (F) is 340 pounds, and the distance between main wheels and nosewheel (L) is 78 inches. The total weight of the airplane (W) is 2,006 pounds. Determine
the CG by using the formula in Figure 3-9.
The CG is 114.8 inches aft of the datum. This is 13.2 inches
forward of the main-wheel weighing points, which proves the location of the datum has no effect on the location of the CG if all measurements are made from the same location.
Datum Aft of the Main Wheels— Nosewheel
Landing Gear
The datum of some aircraft may be located aft of the main
wheels. The airplane in this example is the same one just discussed, but the datum is at the intersection of the trailing edge of the wing with the fuselage. The distance (D) between the datum of the airplane in Figure 3-10 and the main-wheel
3-7Figure 3-13. Determining the CG with datum forward of the main
wheels in an airplane with tailwheel landing gear.CG R × L
W= D +
= 7.5 +
19.7=( )
67 × 222
1,218( )
Figure 3-11. Determining the CG with datum aft of the main wheels
of an airplane with nosewheel landing gear.CG F × L
W= − D +
= − 75 +
−88.2=( )
340 × 78
2,006( )
Figure 3-12. The datum of this tailwheel airplane is the wing root
leading edge.
D = 7.5Datum
229.5L = 222.019.7
Datum
L = 222.0
D = −80
Figure 3-14. The datum is aft of the main wheels, at the intersection
of the wing trailing edge and the fuselage.
CG R × L
W= −D +
= −80 +
= −67.8( )
67 × 222
1,218( )
Figure 3-16. Determining the CG with datum aft of the main wheels
in an airplane with tailwheel landing gear.weighing points is 75 inches, the weight of the nosewheel
(F) is 340 pounds, and the distance between main wheels and nosewheel (L) is 78 inches. The total net weight of the airplane (W) is 2,006 pounds.
The location of the CG may be determined by using the
formula in Figure 3-11.
The CG location is a negative value, which means it is 88.2
inches forward of the datum. This places it 13.2 inches forward of the main wheels, exactly the same location as when it was measured from other datum locations.
Location of Datum
The location of the datum is not important, but all
measurements must be made from the same location.
Datum Forward of the Main Wheels—Tailwheel
Landing Gear
Locating the CG of a tailwheel airplane is done in the same
way as locating it for a nosewheel airplane except the formula is .
The distance (D) between the datum of the airplane in
Figure 3-12 and the main-gear weighing points is 7.5 inches, the weight of the tailwheel (R) is 67 pounds, and the distance (L) between the main-wheel and the tailwheel weighing points is 222 inches. The total weight of the airplane (W) is 1,218 pounds. Determine the CG by using the formula in Figure 3-13 . R × L
WThe CG is 19.7 inches behind the datum.
Datum Aft of the Main Wheels— Tailwheel
Landing Gear
The datum of the airplane in Figure 3-14 is located at the
intersection of the wing root trailing edge and the fuselage.
This places the arm of the main gear (D) at –80 inches. The net weight of the tailwheel (R) is 67 pounds, the distance between the main wheels and the tailwheel (L) is 222 inches, and the total net weight (W) of the airplane is 1,218 pounds.Since the datum is aft of the main wheels, use the formula
found in Figure 3-15.
The CG is 67.8 inches forward of the datum or 12.2 inches aft of the main-gear weighing points. The CG is in exactly the same location relative to the main wheels, regardless of
3-8Figure 3-16. The MAC is the chord drawn through the geographic
center of the plan area of the wing.
CG MAC
Trailing edge mean
aerodynamic chordLeading edge mean
aerodynamic chord
TEMACLEMACDatumwhere the datum is located.
Center of Gravity (CG) and Mean
Aerodynamic Chord (MAC)
Center of Gravity (CG)
In addition to overloading or drastically reducing the
aircraft’s weight, the distribution of weight is also a concern. When aircraft equipment is changed, the person making the equipment change must make an entry on the equipment list indicating items added, removed, or relocated; the date of the change; and the person’s name and certification number in the aircraft’s maintenance records.
For the purpose of weight and balance computations, the CG
of an airplane is an imaginary point about which the nose-heavy (–) moments and tail-heavy (+) moments are exactly equal in magnitude. If suspended from the CG point, the aircraft would have no tendency to rotate nose up or nose down. The CG of the loaded aircraft can range fore and aft within certain limits that are determined during the fl ght test for type certific tion. These limits are the most forward- and rearward-loaded CG positions at which the aircraft meets the performance and flight characteristics required by the FAA.
Any loading that places the CG outside the limits for a
particular aircraft seriously impairs the pilot’s ability to control the aircraft. For example, it is more difficult to take off and gain altitude in a nose-heavy aircraft, and the aircraft tends to drop its nose when the pilot reduces throttle. It also requires a higher speed to land safely. A tail-heavy aircraft is more susceptible to stalling at low speed, which is a concern during the landing approach.
On small airplanes and on all helicopters, the CG location
is identified as being a specific number of inches from the datum. The CG range is identified in the same way. On larger airplanes, from private business jets to large jumbo jets, the CG and its range are typically identified in relation to the width of the wing.
Mean Aerodynamic Chord (MAC)
The width of the wing, or straight-line distance from the
leading edge to the trailing edge, on an airplane is known as the chord. If the leading edge and the trailing edge of a wing are parallel, the chord is equal at all points along the entire length of the wing. The average length of the chord, or MAC, of a tapered wing is more complicated to define. The MAC, as seen in Figure 3-16, is the chord of an imaginary airfoil
that has the same aerodynamic characteristics as the actual airfoil. You can also think of it as the chord drawn through the geographic center of the plan area of the wing.
Usually listed in the aircraft’s TCDS when it is required for weight and balance computations, the MAC is established
by the manufacturer, defining its leading edge (LEMAC)
and trailing edge (TEMAC) in terms of inches from the
datum. [Figure 3-16] The CG location and various limits
are then expressed in percentage of the chord or percent MAC. In order to relate the percent MAC to the datum, all weight and balance information includes two items: the MAC length in inches and the location of the LEMAC in inches from the datum. For the purpose of simplicity, most light-aircraft manufacturers express the CG range in inches from the datum; transport-category aircraft CGs are expressed in percent MAC.
The relative positions of the CG and the aerodynamic
center of lift of the wing have critical effects on the flightcharacteristics of the aircraft. Consequently, relating the CG location to the chord of the wing is convenient from a design and operations standpoint. Normally, an aircraft has acceptable fl ght characteristics if the CG is located somewhere near the 25 percent average chord point. This means the CG is located one-fourth of the distance back from the LEMAC to the TEMAC. Such a location places the CG forward of the aerodynamic center for most airfoils.
The weight and balance data of the airplane in Figure 3-17 states
that the MAC is from stations 144 to 206 and the CG is
located at station 161.
MAC = TEMAC – LEMAC
MAC = 206" – 144" MAC = 62"
3-9Figure 3-18. Formula for determining the CG expressed in percent
MAC.CG inches % MAC = Distance aft of LEMAC × 100
MAC
=
= 27.417 × 100
62Figure 3-17. Large aircraft weight and balance calculation diagram.CG = 27.4%
CG = 161MAC
TEMACLEMACDatum
CG = 27.4 %
CGCG 1= 161161
MAC
Station 144" Station 206"
Figure 3-19. Formula for determining the CG in inches from the
datum.CG inches from datum = LEMAC + MAC × CG % MAC
= 144 +
= 160.962 × 27.4
CG = 161"
In order to find the percent MAC, firs determine the distance
of the CG from LEMAC.
CG – LEMAC = Distance from LEMAC
161" – 144" = 17"
The location of the CG expressed in percent MAC is
determined using the formula found in Figure 3-18. The CG
of the airplane is located at 27.4 percent MAC.
It is sometimes necessary to determine the location of the CG in inches from the datum when its location in percent MAC is known.
The CG of the airplane is located at 27.4 percent MAC.
MAC = 206 – 144 = 62LEMAC = station 144
Determine the location of the CG in inches from the datum
by using the formula found in Figure 3-19.
The CG of this airplane is located at station 160.9 inches aft of the datum. It is important for longitudinal stability that the CG be located ahead of the center of lift of a wing. Since the center of lift is expressed as percent MAC, the location of the CG is expressed in the same terms.
Introduction
This chapter discusses the weight and balance procedures
for light sport aircraft (LSA) that differ from conventional aircraft, specifically weight-shift control (WSC) aircraft (also called trikes), powered parachutes, and amateur-built
LSA. [Figure 4-1]
Light Sport Aircraft Weight
and Balance ControlChapter 4
4-2Figure 4-1. Examples of light sport aircraft (from top left, clockwise): weight-shift control, powered parachute, glider, airplanes, hot
air balloon, and amateur-built LSA.
LSA Definition of Term
LSA is a category of simple, very basic, small, light-weight,
low-performance aircraft, other than a helicopter or powered-lift, and a classification of aircraft specific to the United States. The Federal Aviation Administration (FAA) definesLSA as an aircraft with a maximum gross takeoff weight of not more than 1,320 pounds (600 kg) for aircraft not intended for operation over water, or 1,430 pounds (650 kg) for aircraft intended for operation over water; a maximum airspeed in level flight of 120 knots (220 kilometers per hour (km/h); 140
miles per hour (mph)); a maximum stall speed of 45 knots (83 km/h; 52 mph); a maximum seating capacity of no more than two persons (including the pilot); fixed undercarriage and fixed-pitch or ground-adjustable propeller; and a single reciprocating engine (if powered).
An aircraft that qualifies as LSA may be operated by the
holder of a sport pilot certificate, whether registered as LSA or not. Pilots with a private, recreational, or higher pilot certificate may also fly LSA, even if their medical certificate have expired, as long as they have a valid driver’s license to prove that they are in good enough health to fly. LSA also have less restrictive maintenance requirements and may be maintained and inspected by traditionally certificated aircraft maintenance technicians (AMTs) or by individuals holding
4-3Figure 4-2. CG of a trike.
CG
Aircraft CG• CG is under wing hang point for level flight.
• Center of lift is directly above CG, above the
wing hang point for level flight.
Thrust line is typically designed to be at vertical CG.
Fuel tanka Repairman: Light Sport certificate, and (in some cases) by
their pilots and/or owners.
Weight and Balance
Aircraft such as balloons, powered parachutes, and WSC do
not require weight and balance computations because the load
is suspended below the lifting mechanism. The CG range in these types of aircraft is such that it is difficult to exceed CG limits. For example, the rear seat position and fuel of a WSC aircraft are as close as possible to the hang point with the aircraft in a suspended attitude. Thus, load variations have little effect on the CG. This also holds true for lighter-than-air aircraft, such as a balloon basket or gondola. While it is difficult to exceed CG limits in these aircraft, pilots should never overload an aircraft, as doing so may cause structural damage and/or failures.
Weight affects performance; therefore, pilots should calculate
weight and remain within the manufacturer’s established limits at all times.
WSC Aircraft
WSC aircraft are one- and two-place aircraft that exceed the
criteria of an ultra-light vehicle but do meet the criteria of an
LSA. The definition for WSC can be found in 14 CFR part 1.
A WSC aircraft used for sport and private pilot flying must be registered with an FAA N-number, have an airworthiness certificate, a pilot’s operating handbook (POH), and/or limitations with a weight and loading document aboard.
As mentioned earlier, WSC aircraft are commonly called
trikes. These aircraft have few options for loading because they lack places to put useful load items. One-place trikes have only one seat and a fuel tank, which means the only variables for a flight are amount of fuel and weight of the pilot. Two-place trikes can accommodate a pilot and a passenger. This version may have a small storage bin in addition to the fuel tank.
The most significant factor affecting the weight and balance
of a trike is the weight of the pilot and, if the aircraft has two seats, the weight of the passenger. The trike acts somewhat like a single, main-rotor helicopter because the weight of the aircraft hangs like a pendulum under the wing. Figure 4-2
shows a two-place trike, in which the mast and the nose strut come together slightly below the wing attach point. When the trike is in flight, the weight of the aircraft hangs from the wing attach point. The weight of the engine and fuel is behind this point, the passenger is almost directly below this point, and the pilot is forward of this point. The balance of the aircraft is determined by how all these weights compare. The wing attach point, with respect to the wing keel, is an adjustable location. The attach point is moved slightly forward or slightly aft, depending on the weight of the occupants. For
4-4Figure 4-3. Wing attach point.
Front collar
Trike mast
Keel nose plateControl frame apexDistance from nose
plate to front edge of front collarRear collar adjusted to eliminate gap when
pivot block assembly is against front collar
501/2" to 521/2"example, if the aircraft is flown by a heavy person, the attach
point can be moved farther aft, bringing the wing forward to compensate for the change in CG. Figure 4-3 shows a close-
up of the wing attach point and the small amount of forward and aft movement that is available.
Similar to airplanes, sailplanes, and powered parachutes,
increasing weight creates increases in speed and descent rate. However, the WSC aircraft has a unique characteristic. Adding weight to a WSC aircraft creates more twist in the wing because the outboard leading edges flex more. With less lift at the tips, a nose-up effect is created and the trim speed lowers. Therefore, adding weight can increase speed similar to other aircraft, but reduce the trim speed because of the increased twist unique to the WSC aircraft. Each manufacturer’s make/model has different effects depending on the specific design. For detailed weight and balance information, characteristics, and operating limitations, always reference the specific manufacturer’s manual or POH for the make and model. Figure 4-4 shows an example of a weight
and loading sheet that would be issued with a WSC aircraft. Every aircraft has its own weight and loading data that should come from the manufacturer. The example in Figure 4-4
comes from Airborne, an Australian company, named Airborne XT WSC aircraft. For additional information, refer to the Weight-Shift Control Aircraft Flying Handbook (FAA-H-8083-5).
Powered Parachutes
Powered parachutes have many of the same characteristics
as WSC aircraft when it comes to weight and balance. They have the same limited loading, with only one or two seats, and a fuel tank. A powered parachute acts like a pendulum with the weight of the aircraft hanging beneath the inflated wing (parachute). The point at which the inflated wing attaches to the structure of the aircraft is adjustable to compensate for pilots and passengers of varying weights. With a very heavy pilot, the wing attach point would be moved forward to prevent the aircraft from being too nose heavy. Figure 4-5 illustrates the structure of a powered parachute
and the location of the wing attachment.
A powered parachute used for sport and private flying must
be registered with an FAA N-number, have an airworthiness certificate, a POH, and/or limitations with a weight and balance document aboard. The aircraft must be maintained properly by the aircraft owner, or other qualified personnel, and have the aircraft logbooks available for inspection. Always refer to the POH for weight and balance information specifi to the powered parachute being fl wn. For additional information, refer to the Powered Parachute Flying Handbook (FAA-H-8083-29).
Weight and Balance Computations
(Amateur-Built Aircraft)
A good weight and balance calculation is the keystone
of flight testing an amateur-built aircraft. Accurately determining the aircraft’s takeoff weight and ensuring that the CG is within the aircraft’s design for each flight is critical to conducting a safe flight test
The aircraft should be level when weighed, spanwise and
fore and aft in accordance with the kit manufacturer’s instructions, and should be in the level flight position. It is highly recommended that the aircraft be weighed in an enclosed area using three calibrated scales. Bathroom scales are not recommended because they are not always accurate.
4-5Figure 4-4. Weight and loading for WSC aircraft.
Hang pointKeel rollerRearFrontKeel roller
adjustment holes
U bracketThe effect of changing the hang position is to change the trim speed of the aircraft. Moving the hang point forward
increases trim speed (shorter distances to the datum). The hang point position range may be used on the applicable wings for the entire weight range of the aircraft. CG limits on the trike base/gondola section of the aircraft limits are not critical. The defined hang point position and its limits are defined in this document.
The datum point is the forward bolt on the nose plate (a line between the leading edge pivot bolts on the nose plate) referenced to the hang bolt at the top of the mast for the trike base (gondola).
Moving hang point position is made by
moving the keel roller forward or backward along the keel or by moving the hang point within the U-bracket. A sticker is used on the keel to show the standard position for the keel roller. It lists the keel tube holes used as standard trim points for each model wing. The table below shows the standard keel roller position and the allowable range of CG position/hang bolt position referenced to the nose plate datum.
Diagram of the wing hang point construction, showing keel, U-bracket, and the top of the control frame.
Wing model and maximum takeoff weight
Streak 3
MTO@ 450 kg
Streak 2B
MTOW 450 kgCruze
MTOW 450 kgWizard
MTOW 430 kgStandard trim position and range
Distance from the forward keel roller bolt to forward nose plate bolt
Keel hole 2, second from front
1,340 mm +0 – 20 mmKeel hole 3, third from front1,360 mm ±20 mmKeel hole 3, third from front1,360 mm ±20 mmKeel hole 1, at front1,545 mm +0 – 45 mmDistance from the hang point to forward
nose-plate boltPermissible rear and foremost positionsPermissible U-bracket holes
1,293.5 mm (54.9 in) rear limit
1,353.5 mm (53.3 in) forward limitMiddle U-bracket hole only
1,413.5 mm (55.6 in) rear limit
1,373.5 mm (54.1 in) forward limitFront and middle U-bracket hole only
1,413.5 mm (55.6 in) rear limit
1,373.5 mm (54.1 in) forward limitMiddle U-bracket hole only
1,578.5 mm (61.2 in) rear limit
1,648.5 mm (64.9 in) forward limitAll U-bracket holes permitted
Date
Empty weight
Maximum takeoff weightRegistration
Wing model
Serial numberMake and (trike) base model Airborne XT series/X series aircraft
Applicable wing models Airborne streak 3/Streak 2B/Cruze/Wizard wing
4-6Figure 4-8. Powered parachute.
Introduction
Weight and balance data allows the pilot to determine the
loaded weight of the aircraft and determine whether or not the loaded center of gravity (CG) is within the allowable
range for the weight. See Figure 5-1 for an example of the
data necessary for these calculations.
Single-Engine Aircraft Weight
and Balance ComputationsChapter 5
5-23,200
3,0002,8002,6002,4002,2002,0001,80032 34 36 38 40 42 44 46 48
Fuselage station (in)Loaded aircraft weight (lb)Airplane basic empty weight 1,874.0 lb, EWCG +36.1
CG range (+40.9) to (+46.0) at 3,100 lb
(+33.0) to (+46.0) at 2,250 lb or less
Straight line variation between points
given
Empty weight CG range NoneMaximum weight 3,100 lb takeoff/flight
2,950 lb landing
No. of seats 4 (2 front at +37.0)
(2 rear at +74.0)
Maximum baggage 160 lb
Area A (100 lb at +97.0)
Area B (60 lb at +116.0)
Fuel capacity 92 gal (88 gal usable); two 46 gal
integral tanks in wings at +46.6
Oil capacity 12 qt (−15)
Figure 5-1. Weight and balance data needed to determine proper
loading of a small airplane.
100 lb
max
60 lb
max
Datum Front seats +37 Rear seats +74 Baggage B +116Fuel +46.6 Baggage A +9788 gal usable
EWCG 36.1
Figure 5-2. Airplane loading diagram.
Determining the Loaded Weight and CG
An important part of preflight planning is determining that
the aircraft is loaded so its weight and CG location are within
the allowable limits. The methods of accomplishing this are the manual computational method using weights, arms, and moments; the chart method using weight and moment indexes [Figure 5-2]; and the loading graph method, which eliminates
the need for some mathematical calculations .
Manual Computational Method
The manual computational method uses weights, arms, and
moments. It relates the total weight and CG location to a CG limits chart similar to those included in the Type Certificate
Data Sheet (TCDS) and the Pilot’s Operating Handbook/Aircraft Flight Manual (POH/AFM).
A worksheet, such as the one shown in Figure 5-3, provides
a means to record and compute pertinent weights, arms, and moments for all onboard fuel, personnel, equipment, cargo,
and baggage that is not included in the aircraft’s basic empty
weight (BEW). Figure 5-4 is a sample of a typical equipment
list where many of the pertinent weights and moment values can be found.
As part of preflight planning, fill in the blanks in the
worksheet with the specific data for the flight. The following weights were used to complete the sample weight and balance worksheet in Figure 5-3.
Pilot
................................................................ 120 lb
Front seat passenger ....................................... 180 lb
Rear seat passenger ........................................ 175 lb
Fuel (88 gal) ................................................... 528 lb
Baggage A ...................................................... 100 lb
Baggage B ........................................................ 50 lb
Multiply each item’s weight by its arm to determine the moment. Then, determine the total weight and the sum of the moments. Divide the total moment by the total weight to determine the CG in inches from the datum. For this example, the total weight is 3,027 pounds and the CG is 43.54 inches aft of the datum (a negative result would have indicated a CG forward of the datum).
To determine whether or not the airplane is properly loaded
for this flight, use the CG limits chart. [Figure 5-5] Draw a
line vertically upward from the CG of 43.54 inches and one horizontally to the right from the loaded weight of 3,027 pounds. These lines cross inside the envelope, which shows the airplane is properly loaded for takeoff, but 77 pounds overweight for landing. Note that for this sample chart, the envelope is defined by the solid black line that indicates CG limits at or below the maximum weight for takeoff and landing. There is an additional region identified by a segmented black line that includes weights suitable only for takeoff. It is important to note these subtle differences as they may or may not be found in every POH/AFM.
5-3Item Weight (3,100 lb max.) Arm (in) Moment (lb-in) CG (inches from datum)
67,651.4
+43.54Airplane
Front seats
Rear seats
Fuel (88 gal usable)
Baggage A (100 max.)
Baggage B (60 max.)1,874 36.1
3,027 11,100.0
12,950.0
24,604.8
9,700.0
5,800.0
131,806.2 x =
Figure 5-3. Loading schedule chart derived from loading problem.
* Indicates total weight/arm for all subcomponents
Figure 5-4. Typical equipment list.
5-43,200
3,1003,000
2,9502,900
2,8002,7002,6002,5002,4002,3002,2002,1002,0001,9001,8001,450
1,4001,3501,300
1,250
1,2001,1501,1001,0501,000
+32 +34 +36 +38 +40 +42 +44 +46850 900 950 1,000 1,050 1,100 1,150 1,200
Aircraft CG location
Inches aft of datum (Sta. 0.0)Loaded aircraft weight (lb)
Loaded aircraft weight (kg)Aircraft CG location
Millimeters aft of datum (Sta. 0.0)
CG limits
Takeoff and landing
Takeoff only
If takeoff weight is more than
landing weight of 2,950 pounds, allow flight time for fuel burn-off to 2,950 pounds before landing
Figure 5-5. CG limits chart from a typical POH.
Loading Graph Method
The charts and graphs found in the POH/AFM can help
simplify and expedite the preflight weight and balance computation process. Some use a loading graph and moment indexes rather than the arms and moments. These charts eliminate the need for calculating moments and make computations quicker and easier. [Figure 5-6]
Moment Indexes
Moments determined by multiplying the weight of each component by its arm result in large numbers that are awkward to calculate and can become a source of mathematical error. To eliminate these large numbers, moment indexes are sometimes used. The moment is divided by a reduction factor, such as 100 or 1,000, to get the moment index. The loading graph provides the moment index for each component to avoid mathematical calculations. The CG envelope uses moment indexes rather than arms and moments.The CG limits envelope is the enclosed area on a graph of the airplane loaded weight and the CG location. If lines drawn from the weight and CG cross within this envelope, the airplane is properly loaded.
Loading Graph
Figure 5-6 is a typical loading graph taken from the POH of a modern four-place airplane. It is a graph of load weight and load moment indexes. Diagonal lines for each item relate the weight to the moment index without having to use mathematical calculations.
Compute Weight and Balance Using the Loading
Graph
To compute the weight and balance using the loading graph
in Figure 5-6 , make a loading schedule chart like the one
in Figure 5-7 . In Figure 5-6, follow the horizontal line for
300 pounds load weight to the right until it intersects the diagonal line for pilot and front passenger. From this point, drop a line vertically to the load moment index along the bottom to determine the load moment for the front seat
occupants. This is 11.1 lb -in divided by 1,000. Record it in
the loading schedule chart. Determine the load moment for the 175 pounds of rear seat occupants along the diagonal for second row passengers or cargo. This is 12.9; record it in the loading schedule chart.
Determine the load moment for the fuel and the baggage
in areas A and B in the same way and enter them all in the loading schedule chart. The maximum fuel is marked on the diagonal line for fuel in terms of gallons or liters. The maximum is 88 gallons of usable fuel. The total capacity is 92 gallons, but in our example, 4 gallons are unusable and have already been included in the empty weight of the aircraft. The weight of 88 gallons of fuel is 528 pounds and its moment index is 24.6. The 100 pounds of baggage in area A has a moment index of 9.7 and the 50 pounds in area B has an index of 5.8. Enter all of these weights and moment indexes in the loading schedule chart and add all of the weights and moment indexes to determine the totals.
Transfer totals to the CG moment envelope in Figure 5-8.
The CG moment envelope is an enclosed area on a graph
of the airplane loaded weight and loaded moment. If lines drawn from the weight and loaded moment cross within this envelope, the airplane is properly loaded. The loading schedule from the example in Figure 5-7 shows that the total
weight of the loaded aircraft is 3,027 pounds, and the loaded airplane moment divided by 1,000 is 131.8.
22520017515012510075502500 5 10 15 20 25 30 350 50 100 150 200 250 300 350 400
Load moment/1,000 (lb-in)Load weight (lb)
Load weight (kg)Load moment/1,000 (kg-mm)
Note: Line representing adjustable seats shows pilot and front seat passenger CG on adjustable seat positioned for an
average occupant. Refer to the Loading Arrangements diagram for forward and aft limits of occupant CG range. 80 (302.8)
70 (265.0)
65 gal reduced
Loading graph60 (227.1)
50 (189.3)
40 (151.4)
30 (113.6)
20 (75.7)
10 (37.9)88 gal max (333.1liters)
Baggage (Area “B”) (60 lb max)Baggage (Area “A ”) (100 lb max)Fuel (6 lb/gal)
Pilot & front passenger2nd row passengers or cargo
Figure 5-6. Typical loading graph.
Figure 5-7. Loading schedule chart.Item Weight Moment/1,000
67.7 Airplane (BEW)
Front seats
Rear seats
Fuel
Baggage A
Baggage B
Total1,874
3,02711.112.924.6
5-63,200
3,1003,000
2,9502,900
2,8002,7002,6002,5002,4002,3002,2002,1002,0001,9001,8001,450
1,4001,3501,3001,2501,2001,1501,1001,0501,000
55 65 75 85 95 105 115 125 135 145 650 850 1,050 1,250 1,450 1,650 750 950 1,150 1,350 1,550
Loaded aircraft moment/1,000 (lb-in)Loaded aircraft weight (lb)
Loaded aircraft weight (kg)Loaded aircraft moment/1,000 (kg-mm)
Center of gravity
Moment envelope
Takeoff and landing
Takeoff only
If takeoff weight is more than
landing weight of 2,950 pounds,
allow flight time for fuel burn-off
to 2,950 pounds before landing.
Figure 5-8. CG moment envelope.
Referring to Figure 5-8, draw a line vertically upward from
131.8 on the horizontal index at the bottom of the chart and
a horizontal line from 3,027 pounds in the left-vertical index. These lines intersect within the dashed area, which shows that the aircraft is loaded properly for takeoff, but it is too heavy for landing (similar to the previous example). Because of this, if the aircraft had to return for landing immediately after takeoff, it would need to fly long enough to burn 77 pounds (slightly less than 13 gallons) of fuel to reduce its weight for landing.
Introduction
Weight and balance computations for small multiengine
airplanes are similar to those discussed for single-engine airplanes. See Figure 6-1 for an example of weight and
balance data for a typical light twin-engine airplane.
Multiengine Aircraft
Weight and Balance
ComputationsChapter 6
6-2Figure 6-1. Typical weight and balance data for a light twin-engine
airplane.
Datum Forward face of fuselage bulkhead ahead of
rudder pedals
Seats 2 at 37.0
2 at 75.0
1 at 113.0: 200 lb limit
Fuel 213.4 gal (2 wing tanks, 105.0 gal each 103.0 gal
usable at +61.0)
Undrainable fuel: 1.6 lb at +62
Oil 24 quarts (12 quarts in each engine): −3.3
Baggage Forward 100 lb limit : −15
Aft 200 lb limit: +113
CG Range (+38) to (+43.1) at 5,200 lb
(+43.6) at 4,800 lb
(+32) to (+43.6) at 4,300 lb or less
Straight line variation between points given
Engine 2 240-horsepower horizontally opposed engines
Fuel burn: 24 gph for 65% cruise at 175 knots
29 gph for 75% cruise at 180 knots
Datum
Front seats +37 2nd seats +75 3rd seat or baggage limit 200 lb +113
Fuel +61100 lb baggage −15EWCG 35.2832.0 43.6CG limits
MAC = 61.6 20.1
Figure 6-2. Twin-engine airplane weight and balance diagram.
Item Weight (lb) (5,200 max.) Arm (in) Moment (lb-in) CG
120,093
51,240
11,84023,250
−1,500
10,170
215,093 42.47Airplane
Fuel (140 gal)
Front seat
Row 2 seats
Foward baggage
Aft baggage
Total3,404
5,06435.28
−15.0
113.0x =
Figure 6-3. Determining the loaded CG of the sample airplane in Figure 6-2.The airplane in this example was weighed to determine its
basic empty weight (BEW) and empty weight center of
gravity (EWCG). The weighing conditions and results are:Weight with fuel drained and oil full:
Right wheel scales ........................ 1,084 lb, tare 8 lb
Left wheel scales .......................... 1,148 lb, tare 8 lb
Nose wheel scales ....................... 1,202 lb, tare 14 lb
Determine the Loaded CG
First, add the weights indicated by the individual scales and then subtract the tare weights to determine the BEW. Next, using the BEW and EWCG, the loaded weight and CG of the aircraft can be determined with data from Figure 6-2, using
a chart such as the one in Figure 6-3.
The aircraft is loaded as shown:
Fuel (140 gal)
................................................ 840 lb
Front seats ..................................................... 320 lb
Row 2 seats .................................................... 310 lb
Forward baggage ........................................... 100 lb
Aft baggage ..................................................... 90 lb
Chart Method Using Weight, Arm, and Moments
Make a chart showing the weight, arm, and moments of the
airplane and its load.
6-35,200
5,0004,8004,6004,4004,2004,000
32 34 36 38 40 42 44
Inches from the datumWeight (lb)
Figure 6-4. Sample CG range chart.
CG in % MACCG in inches from LEMAC x 100
MAC=
22.37 x 100
61.6=
36.3% MAC=
Figure 6-5. Finding CG in percent MAC.The loaded weight for this fl ght is 5,064 pounds, and the CG
is located at 42.47 inches aft of the datum.
To determine that the weight and CG are within the allowable
range, refer to the CG range chart in Figure 6-4. Draw a line
vertically upward from 42.47 inches from the datum and one horizontally from 5,064 pounds. These lines cross inside the envelope, showing that the airplane is properly loaded.
Determining the CG in Percentage of Mean
Aerodynamic Chord (MAC)
Refer again to Figures 6-2 and 6-3.
The loaded CG is 42.47 inches aft of the datum.
The MAC is 61.6 inches long.The LEMAC is located at station 20.1.The CG is 42.47 – 20.1 = 22.37 inches aft of LEMAC.
Use the formula in Figure 6-5 to find the CG in percent MAC.
The loaded CG is located at 36.3 percent MAC.The Chart Method Using Weight and Moment
Indexes
As mentioned in the previous chapter, anything that can be
done to make careful preflight planning easier makes flyingsafer. Many manufacturers furnish charts in the Pilot’s Operating Handbook/Aircraft Flight Manual (POH/AFM) that use weight and moment indexes rather than weight, arm, and moments. The charts also help reduce errors by including tables of moment indexes for the various weights.
Consider the loading for this particular flight
Cruise fuel flow = 16 gallons per hou
Estimated time en route = 2 hours, 10 minutesReserve fuel = 45 minutes = 12 gallonsTotal required fuel = 47 gallons
The pilot completes a chart like the one in Figure 6-6 using
moment indexes from tables in Figures 6-7 and 6-8.
The moments divided by 100 in the index column are found
in the charts in Figures 6-7 through 6-9. If the exact weight
is not in the chart, interpolate between the weights that are included. When a weight is greater than any of those shown in the charts, add the moment indexes for a combination of weights to get that which is desired. For example, to get the moments divided by 100 for the 320 pounds in the front seats, add the moment index for 100 pounds (105) to that for 220 pounds (231). This gives the moment index of 336 for 320 pounds in the front seats.
Use the moment limits versus weight envelope in Figure 6-10
to determine if the weight and balance conditions are
within allowable limits for both takeoff and landing at the destination. The moment limits versus weight envelope is an enclosed area on a graph of three parameters. The diagonal line representing the moment divided by 100 crosses the horizontal line representing the weight at the vertical line representing the CG location in inches aft of the datum. When the lines cross inside the envelope, the aircraft is loaded within its weight and CG limits.
Takeoff: – 3,781 lb and 4,296 moment divided by 100
Landing: – 3,571 lb and 4,050 moment divided by 100
6-4Weight and Balance Loading Fo rm
Model _________________________________________________ Date ____________________________________________________
Serial Number ___________________________________________ Reg. Number _____________________________________________
Item Pounds (3,900 max.) Inde x moment/100
Airplane basic empty weight
Front seat occupants
Row 2 seats
Baggage (200 lb max.)Subtotal Z ero fuel condition (3,500 max.)
F uel loading (gallons)
Subtotal R amp condition
*
Less fuel for start, taxi, and takeoff
Subtotal
Takeoff condition
L ess fuel to destination (gallons)
Landing condition
* Fuel for start, taxi, and takeoff is normally 24 pounds at a moment index of 28.2,625
3,325
3,805
−24
3,781
−210
3,5712,864
3,762
4,324
−28
4,296
−246
4,05080
Figure 6-6. Typical weight and balance loading form.
Occupant Moments/100
WeightFront seats
Arm +105Row 2 seats
Arm +142
110120130140150160170180190200210220230240250105116126137147158168179189200210221231242252263142156170185199213227241256270284298312327341355
Figure 6-7. Sample weight and moment index for occupants.Locate the moment divided by 100 diagonal line for 4,296 and
follow it down until it crosses the horizontal line for 3,781 pounds. These lines cross inside the envelope at the vertical line for a CG location of 114 (113.6) inches aft of the datum.
The maximum allowable takeoff weight is 3,900 pounds, and
this airplane weighs 3,781 pounds. The CG limits for 3,781 pounds are 109.8 to 117.5. The CG of 114 (113.6) inches falls within these allowable limits.
6-5Baggage Moments/100
Weight Arm +167
2030405060708090
1001101201301401501601701801902001733506784
100117134150167184200217234251267284301317334
Figure 6-8. Sample weight and moment index for baggage.
Usable Fuel – Arm +117
Gallons Pounds Moment/100
102030405060708090
12018024030036042048054060070
140211281351421491562632702
Figure 6-9. Sample weight and moment index for fuel.
6-64,000
3,9003,800
3,600
3,5003,400
3,200
3,000
2,800
2,6002,400
106 108 110 112 114 116 118
CG inches aft of datum
Weight (lb)3,9004,600 4,500 4,400 4,300 4,200
4,100
4,000
3,800
3,700
3,600
3,500
3,400
3,1003,300
3,200
3,000
2,900
2,800
2,700
2,600Maximum zero fuel weight
Moment/100
Envelope based on the following weight and CG limit data (landing gear down)
Weight condition FWD CG limit Aft CG limit
3,900 pounds (max takeoff/landing) 110.6 117.5
3,250 pounds or less 106.6 117.5Maximum takeoff
and landing weight
Figure 6-10. Sample moment limits versus weight envelope.
Introduction
The largest weight changes that occur during the lifetime of
an aircraft are those caused by alterations and repairs. It is the responsibility of the FAA-certificated mechanic or repairman doing the work to accurately document the weight change and record it in both the maintenance records and the Pilot’s Operating Handbook/Aircraft Flight Manual (POH/AFM).
Center of Gravity Change After
a Repair or AlterationChapter 7
7-2Figure 7-1. A typical 14 CFR part 23 weight and balance record.
Weight and Balance Record
(Continuous history of changes in structure or equipment affecting weight and balance)
Airplane Model Serial Number Page Number
DateItem No.
In OutDescription
of Article or
ModificationWeight Change Running
Basic Empty
Weight Added (+) Removed (−)
Wt.
(lb)Wt.
(lb)Arm
(in)Moment/
1,000Wt.
(lb)Arm
(in)Moment/
1,000Moment/
1,000
As delivered 1,876 67.8
8-7-09 Alteration per FAA Form 337
Dated 8-7-09 7.38 .346 1,883.4 68.1
34-XX Turn coordinator –2.5 15.0 –.037 1,880.9 68.1
34-XX Directional gyro –3.12 13.5 –.042 1,877.8 68.1
22-XX Autopilot system 13.0 32.7 .425 1,890.8 68.5Cessna 182L 1 18259080Equipment List
The Federal Aviation Administration (FAA) considers
the addition or removal of equipment included in the Comprehensive Equipment List to be a minor alteration. The weights and arms are included with the items in the equipment list, and these minor alterations can be done and the aircraft approved for return to service by an FAA-certificate mechanic or repairman. The only documentation required is an entry in the aircraft maintenance records and the appropriate change to the weight and balance record in the POH/AFM. [Figure 7-1]
Figure 7-2 is a comprehensive list of all Cessna equipment
that is available for the Model 182S airplane. It should
not be confused with the airplane-specific equipment list. An airplane-s pecifi c list is provided with each individual
airplane at delivery and is typically found at the end of the Pilot’s Operating Handbook. The following comprehensive equipment list and the airplane-specific list have a similar order of listing.
The comprehensive equipment list provides the following
information in column form:
In the Item No column, each item is assigned a coded number.
The first two digits of the code represent the assignment of an equipment item within the ATA Specification 100 breakdown (Chapter 11 for Placards, Chapter 21 for Air Conditioning, Chapter 77 for Engine Indicating, etc.). These assignments also correspond to the Maintenance Manual chapter breakdown for the airplane. Items receive a unique sequence number (01, 02, 03, etc.). After the sequence number (and hyphen), a suffix letter is assigned to identify an equipment item as required, standard, or optional. Suffixletters are as follows:
–R = required item or equipment for FAA certificatio
–S = standard equipment item
–O = optional equipment item replacing required or
standard item(s)
–A = optional equipment item that is in addition to
required or standard items
In the Equipment List Description column, each item is
assigned a descriptive name to help identify its function.
In the Ref Drawing column, a drawing number is provided
that corresponds to the item.
Note: Additional equipment must be installed in accordance
with the reference drawing, service bulletin, or a separate FAA approval.
In the Wt and Arm columns, you find the weight in pounds
and arm in inches of the equipment item.
Notes: Unless otherwise indicated, true values (not net
change values) for the weight and arm are shown. Positive arms are distances aft of the airplane datum; negative arms are distances forward of the datum. Asterisks (*) in the weight and arm column indicate complete assembly installations. Some major components of the assembly are listed on the lines immediately following. The sum of these major components does not necessarily equal the complete assembly installation.
7-3Figure 7-2. Typical comprehensive equipment list.* Indicates total weight/arm for all subcomponents
Major Alteration and Repair
Within the following text, information concerning major
repairs or major alterations does not apply to any aircraft within the light-sport category. This category of aircraft is not eligible for major repairs or alterations.
Any major alteration or repair requires the work to be done
by an FAA-certificated mechanic or repairman or facility. The work must be checked for conformity to FAA-approved data and signed off by an aircraft mechanic holding an Inspection Authorization (IA) or by an authorized agent of an appropriately rated FAA-approved repair station. A Repair Station record and/or FAA form 337, Major Repair and Alteration, must be completed describing the work. (Reference Title 14 of the Code of Federal Regulations (14 CFR) part 43, appendix B, for the recording of major repair and alterations requirements.) A dated and signed revision to the weight and balance record is made and kept with the maintenance records, and the airplane’s new empty weight and empty weight arm or moment index are entered in the POH/AFM.Weight and Balance Revision Record
Aircraft manufacturers use different formats for their weight and balance data, but Figure 7-3 is typical of a weight and
balance revision record. All weight and balance records should be kept with the other aircraft records. Each revision record should be identified by the date, the aircraft make, model, and serial number. The pages should be signed by the person making the revision and his or her certificate type and number must be included.
The computations for a weight and balance revision
are included on a weight and balance revision form. Appropriate fore-and-aft extreme loading conditions should be investigated and the computations shown. The date those computations were made is shown in the upper right corner of Figure 7-3. When this work is superseded, a notation
must be made on the new weight and balance revision form, including a statement that the new computations supersede the computations dated “MM/DD/YY.”
7-4Figure 7-3. A typical airplane weight and balance revision record.
Weight & Balance
Cessna 182L
N42565S/N 18259080
Removed the following equipment:
1. Turn coordinator P/N C661003-0201
2. Directional gyro P/N 0706000
Installed the following equipment:
1. S-TEC System 40 autopilot, includes turn coordinator and directional gyro
*REVISED LICENSED EMPTY WEIGHT NEW USEFUL LOAD 1,216.62
Forward check (Limit +33.0)
Wt. × Arm = Moment
A/C empty Fwd. seatsAft seatsFuel (min.)Baggage ABaggage B
Jeseph P. Kline
A&P 123456789Supersedes computations of FAA Form337 dated 10/02/07.
Weight x Arm = Moment
2.50 lb 15.0 37.50
+3.12 lb 13.5 +42.12 5.62 79.62
1,876.00 36.14 67,798.64
−5.62 −79.62
1,870.38 36.20 67,719.02
Weight x Arm = Moment
13 lb 32.70 425.13
1,870.38 36.20 67,719.02
+13.00 +425.13
1,883.38 36.18 68,144.15
Rearward check (Limit +46.0)
A/C empty
Fwd. seatsAft seatsFuel (min.)Baggage ABaggage B1,883.38 36.18 68,144.15 170.00 37.00 6,290.00
115.00 48.00 5,520.00
2,168.38 +36.87 79,954.15Total
Aircraft after removal:
Wt. × Arm = Moment 1,883.38 36.18 68,144.15
170.00 37.00 6,290.00 340.00 74.00 25,160.00 528.00 48.20 25,449.60 100.00 97.00 9,700.00 60.00 116.00 6,960.003,081.38 45.98 141,703.75
Date: 08/07/09
7-5Figure 7-4. Weight, arm, and moment changes caused by typical alteration or repair.Item Weight (lb) Arm (in) Moment (lb-in) New CG
67,723.6
−192.8
−874.0−432.0+122.6+229.5
+2,037.0
68,613.9 +36.4Airplane
Radio removed
Power supply removed
ELT removed
Radio installed
ELT installed
Passenger seat installed
Total1,876.0
−12.2
−9.2−3.2+8.4+1.7
+21.0
1,882.536.1
97.0x =
Figure 7-5. Weight and moment index changes caused by a typical alteration or repair.Item Weight (lb) Moment indexes (lb-in/100) New CG (inches from datum)
+677.2
−1.93−8.74
−4.32
+1.23+2.29
+20.37
+686.1 +36.4Airplane
Radio removed
Power supply removed
ELT removed
Radio installed
ELT installed
Passenger seat installed
Total1,876.0
−12.2
−9.2
−3.2
+8.4+1.7
+21.0
1,882.5The weight and balance revision sheet should clearly show
the revised empty weight, empty weight arm and/or moment
index, and the new useful load. An example of these entries can be found at the bottom of Figure 7-3.
Weight Changes Caused by a Repair or
Alteration
A typical alteration might consist of removing two pieces of radio equipment from the instrument panel and a power supply that was located in the baggage compartment behind the rear seat. In this example, these two pieces are replaced with a single lightweight, self-contained radio. At the same time, an old emergency locator transmitter (ELT) is removed from its mount near the tail, and a lighter weight unit is installed. A passenger seat is installed in the baggage compartment.Computations Using Weight, Arm, and Moment
The first step in the weight and balance computation is to make a chart like the one in Figure 7-4, listing all of the
items that are involved. The new center of gravity (CG) of 36.4 inches aft of the datum is determined by dividing the new moment by the new weight.
Computations Using Weight and Moment Indexes
If the weight and balance data uses moment indexes rather
than arms and moments, this same alteration can be computed using a chart such as the one in Figure 7-5. Subtract the
weight and moment indexes of all the removed equipment from the empty weight and moment index of the airplane. Add the weight and moment indexes of all equipment installed to determine the total weight and the total moment index. To determine the position of the new CG in inches aft of the datum, multiply the total moment index by 100 to get the moment, and divide this by the total weight to get the new CG.
7-6Figure 7-8. Formula for determining the CG in percent MAC.CG in % MACCG in inches from LEMAC x 100
MAC=
10.42 x 100
58.0=
17.9% MAC=Figure 7-7. Loading conditions.CG
range
Datum Front seats Rear seats +74 Baggage B +116Fuel +48.2 Baggage A +97Forward
limitAft limit 46.0
Figure 7-6. Weight and balance information.3,200
3,0002,8002,6002,4002,2002,0001,80032 34 36 38 40 42 44 46 48
Fuselage station (in)Loaded aircraft weight (lb)Airplane EW and EWCG 1,876.0 lb at +36.14
Engine METO horsepower 230CG range (+40.9) to (+46.0) at 3,100 lb
(+33.0) to (+46.0) at 2,250 lb or less
Straight line variation between points given
Empty weight CG range NoneMaximum weight 3,100 lb takeoff/flight 2,950 lb landing
Datum to LEMAC 25.98MAC 58.00
No. of seats 4 (2 front at +34.0)
(2 rear at +74.0)
Fuel capacity 92 gal (88 gal usable)
two 46-gal integral tanks in wings at +48.2
See NOTE 1 for data on unusable fuel.
Minimum fuel (METO HP
÷ 2) 115 lb at +48
Maximum baggage 160 lb Area A (100 lb at +97.0)
Area B (60 lb at +116.0
Oil capacity 12 qt (−15) (6 qt usable)
See NOTE 1 for data on undrainable oil.
NOTE 1: The certificated empty weight and corresponding center ofgravity location must include unusable fuel of 30 lb (+46) and undrainable oil of 0 lb. Determining the CG in Percentage of Mean
Aerodynamic Chord (Percent MAC)
This procedure is the same as found in Chapter 5, Single-
Engine Aircraft Weight and Balance Computations. Refer to the load conditions and CG information found in Figures 7-5, 7-6, and 7-7 to compute the CG in percent MAC:
The loaded CG is +36.4 inches aft of the datum.
The MAC is 58.0 inches long.
The leading edge mean aerodynamic chord (LEMAC)
is located at station 25.98.
The CG is +36.4 – 25.98 = 10.42 inches aft of LEMAC.
Use the formula in Figure 7-8 to determine CG in MAC
percentages.
The loaded CG after alteration or repair is located at 17.9
percent MAC.
Empty Weight CG (EWCG) Range
The fuel tanks, seats, and baggage compartments of some aircraft are so located that changes in the fuel or occupant load have a very limited effect on the balance of the aircraft. Aircraft of such a configuration show an empty weight CG (EWCG) range in the Type Certificate Data Sheet (TCDS).
If the EWCG is located within this range, it is impossible to legally load the aircraft so that its loaded CG falls outside its allowable range.
If the TCDS lists an EWCG range, and after the alteration is
completed the EWCG falls within this range, then there is no need to compute a fore and aft check for adverse loading. But if the TCDS lists the EWCG range as “None” (and most of them do), a check must be made to determine whether or not it is possible by any combination of legal loading to cause the aircraft CG to move outside of either its forward or aft limits.
Adverse-Load CG Checks
Many modern aircraft have multiple rows of seats and often more than one baggage compartment. After any repair or alteration that changes the weight and balance, the Airframe and Powerplant (A&P) FAA-certificated mechanic or repairman must ensure that no legal condition of loading can
7-7Figure 7-9. Load conditions for forward adverse-load CG check.Item Weight (lb) Arm (in) Moment (lb-in) Most forward CG +33.0
67,798.6
5,780.0
5,520.0
79,098.6 +36.6Airplane (empty)
Pilot
Fuel (minimum)
Total1,876.0
2,161.036.14
34.048.0x =When rear row of seats is occupied, 120 pounds of
baggage or ballast must be carried in forward baggage compartment. For additional loading instruction, see Weight and Balance Data.
Figure 7-11. Typical baggage compartment placard.
Figure 7-10. Load conditions for aft adverse-load CG check.Item Weight (lb) Arm (in) Moment (lb-in) Most Aft CG +46.0
67,798.6
5,780.0
25,449.6
25,160.0
9,700.06,960.0
140,848.2 +45.8Airplane (empty)
Pilot
Fuel (full tanks – 88 gal)Rear seat occupants (2)
Baggage ABaggage B
Total1,876.0
170.0528.0340.0100.0
3,074.0 36.14 34.0
48.2 74.0 97.0 116.0
x =move the CG outside of its allowable limits. To determine
this, adverse-loaded CG checks must be performed and the results noted in the weight and balance revision sheet. [Figure 7-3]
Forward Adverse-Load CG Check
To conduct a forward CG check, make a chart that includes
the airplane and any occupants and items of the load located in front of the forward CG limit. Include only those items behind the forward limit that are essential to flight: the pilot, and the minimum fuel.
In this example, the pilot, whose nominal weight is 170
pounds, is behind the forward CG limit. The fuel is also behind the forward limit, so the minimum fuel is used. For weight and balance purposes, the minimum fuel is no more than the quantity needed for one-half hour of operation at rated maximum continuous power. This is considered to be
1⁄12 gallon for each maximum except takeoff (METO)
horsepower. Because aviation gasoline weighs 6 pounds per gallon, determine the number of pounds of the minimum fuel by dividing the METO horsepower by two. In this example, minimum fuel is 115 pounds. The front and rear seats and the baggage are all behind the forward CG limit, so no passengers or baggage are considered.
Make a chart like the one in Figure 7-9 to determine the CG
with the aircraft loaded for its most forward CG. With the
load consisting of only a pilot and the minimum fuel, the CG is +36.6, which is behind the most forward allowable limit for this weight of +33.0.Aft Adverse-Load CG Check
To conduct an aft or rearward CG check, make a chart that
includes the empty weight and EWCG of the aircraft after the alteration and all occupants and items of the load behind the aft CG limit of 46.0. The pilot is in front of this limit but is essential for flight and must be included. In this example, only the pilot occupies the front seats. Since the CG of the fuel is behind the aft limit, full fuel is used, as well as the nominal weight (170 lb) for both rear seat passengers and the maximum allowable baggage.
Under these loading conditions, the CG is located at +45.8,
which is ahead of the aft limit of +46.0. [Figure 7-10] With
only the pilot in front of the aft CG limit and maximum of all items behind the aft limit, the CG is at +45.8 inches, which is ahead of the aft limit of +46.0 inches.
Ballast
It is possible to load most modern airplanes so the CG shifts outside of the allowable limit. Placards and loading instructions in the weight and balance data inform the pilot of the restrictions that prevent such a shift from occurring. A typical placard in the baggage compartment of an airplane
is shown in Figure 7-11. When the CG of an aircraft falls
outside of the limits, it can usually be brought back in by using ballast.
7-8Figure 7-13. Formula for determining ballast.Ballast weightAircraft empty weight × Dist. out of limits
Distance between ballast and desired CG=Temporary Ballast
Temporary ballast, in the form of lead bars or heavy canvas
bags of sand or lead shot, is often carried in the baggage compartments to adjust the balance for certain flight conditions. The bags are marked “Ballast XX Pounds—Removal Requires Weight and Balance Check.” Temporary ballast must be secured so it cannot shift its location in flight and the structural limits of the baggage compartment must not be exceeded. All temporary ballast must be removed before the aircraft is weighed.
Temporary Ballast Formula
The CG of a loaded airplane can be moved into its allowable
range by shifting passengers or cargo or by adding temporary ballast.
Permanent Ballast
If a repair or alteration causes the aircraft CG to fall outside
of its limit, permanent ballast can be installed. Usually permanent ballast is made of blocks of lead painted red and marked “Permanent Ballast—Do Not Remove.” It should be attached to the structure so that it does not interfere with any control action and attached rigidly enough that it cannot be dislodged by any flight maneuvers or rough landing
Two things must first be known to determine the amount of
ballast needed to bring the CG within limits: the amount the CG is out of limits, and the distance between the location of the ballast and the limit that is affected.
If an airplane with an empty weight of 1,876 pounds has been
altered so its EWCG is +32.2, and CG range for weights up to 2,250 pounds is +33.0 to +46.0, permanent ballast must be installed to move the EWCG from +32.2 to +33.0. There is a bulkhead at fuselage station 228 strong enough to support the ballast.To determine the amount of ballast needed, use the formula in Figure 7-13.
Ballast needed = 1.876 × 0.8
= 1500.8
= 7.7 pounds
A block of lead weighing 7.7 pounds, attached to the bulkhead
at fuselage station 228, moves the EWCG back to its proper forward limit of +33. This block should be painted red and marked “Permanent Ballast—Do Not Remove.”
Introduction
Weight and balance considerations of a helicopter are similar
to those of an airplane, except they are far more critical, and the center of gravity (CG) range is much more limited. [Figures 8-1 and 8-2] The engineers who design a helicopter
determine the amount of cyclic control authority that is available, and establish both the longitudinal and lateral CG envelopes that allow the pilot to load the helicopter so there is sufficient cyclic control for all flight conditionsWeight and Balance Control—
HelicopterChapter 8
8-2Figure 8-1. Weight and balance data needed to determine proper
loading of a helicopter.Helicopter basic empty weight 1,545.0 lb, EWCG +101.4
(+0.2 lateral offset)
CG range (+92.0) to (+98.0) at 1,600 lb
(+92.0) to (+95.0) at 2,250 lb
Empty weight CG range NoneMaximum weight 2,250 lb
Number of seats 2 at (+64.0) (L−13.5) (R+13.5)
lateral offset
Maximum baggage (100 lb) at +105.0 (0.0 lateral offset)
Fuel capacity 50 gal (48 gal usable);
288 lb at (+96.0) (−8.4 lateral offset)
Oil capacity 4.3 qt at (+90) (0.0 lateral)
Figure 8-2. Typical helicopter datum, flight stations, and butt line
locations.Datum FS 0.0 FS 68.0 FS 254.5
BL 27.4 R
BL −38.7 LBL 0Butt
line zero
Figure 8-3. Typical helicopter CG envelopes.2,400
2,2002,0001,8001,60092 94 96 98 100
Longitudinal CG (inches aft of datum)Gross Weight (lb)Longitudinal CG Envelope
Approved Area2,203
2,027
1,877
94.4 95.0 98.2
2,300
2,2002,1002,0001,9001,8001,7001,600
−5,000 −3,000 −1,000 0 1,000 3,000 5,000
Left Lateral Offset Moment Right
(lb-in)Gross Weight (lb)Lateral Offset Moment Envelope
2,203
2,027
1,877
−1,705 −326 1,699If the CG is ahead of the forward limit, the helicopter tilts
and the rotor disk has a forward pull. To counteract this
and maintain a stationary position, rearward cyclic stick displacement would be required. If the CG is too far forward, there may not be enough available cyclic authority to allow the helicopter to flare during landing, and it consequently requires an excessive landing distance.
If the CG is aft of the allowable limits, the helicopter flies
with a tail-low attitude and may need more forward cyclic stick displacement than is available to maintain a hover in a no-wind condition. There might not be enough cyclic travel to prevent the tail boom from striking the ground. If gusty winds should cause the helicopter to pitch up during high speed fl ght, there might not be enough forward cyclic control to safely lower the nose.
Helicopters are approved for a specifi maximum gross
weight, but it is not safe to operate them at this weight under some conditions. A high density altitude decreases the safe maximum weight as it affects the hovering, takeoff, climb, autorotation, and landing performance.The fuel tanks on some helicopters are behind the CG, causing it to shift forward as fuel is used. Under some flightconditions, the balance may shift enough that there is not sufficient cyclic authority to flare for landing. For these helicopters, the loaded CG should be computed for both takeoff and landing weights.
Lateral balance of an airplane is usually of little concern
and is not normally calculated. Some helicopters, especially those equipped for hoist operations, are sensitive to the lateral position of the CG and their Pilot’s Operating Handbook/Rotorcraft Flight Manual (POH/RFM) include both longitudinal and lateral CG envelopes, as well as information on the maximum permissible hoist load. Figure 8-3 is an
example of such CG envelopes.
8-3Determining the Loaded CG of a
Helicopter
The empty weight and empty weight center of gravity
(EWCG) of a helicopter are determined in the same way
as for an airplane. See Chapter 5, Single-Engine Aircraft Weight and Balance Computations. The weights recorded on the scales supporting the helicopter are added and their distances from the datum are used to compute the moments at each weighing point. The total moment is divided by the total weight to determine the location of the CG in inches from the datum. The datum of some helicopters is located at the center of the rotor mast, but since this causes some arms to be positive (behind the datum) and others negative (ahead of the datum), most modern helicopters have the datum located ahead of the aircraft, as do most modern airplanes. When the datum is ahead of the aircraft, all longitudinal arms are positive.
The lateral CG is determined in the same way as the
longitudinal CG, except the distances between the scales and
butt line zero (BL 0) are used as the arms. Arms to the right of BL 0 are positive and those to the left are negative. The butt line zero (or sometimes referred to as the buttock) is a line through the symmetrical center of an aircraft from nose to tail. It serves as the datum for measuring the arms used to find the lateral CG. Lateral moments that cause the aircraft to roll clockwise are positive (+), and those that cause it to roll counterclockwise are negative (–).
To determine whether or not a helicopter is within both
longitudinal and lateral weight and balance limits, construct a table like the one in Figure 8-4, with the following data
specific to the aircraft
Empty weight
..................................... 1,545 lb
EWCG ................................................ 101.4 inches aft of
the datum
Lateral balance ................................... arm 0.2 inches right
of BL 0
Maximum allowable gross weight ..... 2,250 lb
Pilot .................................................... 200 lb @ 64 inches
aft of datum and 13.5 inches right of BL 0
Passenger
........................................... 170 lb @ 64 inches
aft of datum and –13.5 in left of BL 0
Fuel (48 gal)
....................................... 288 lb @ 96 inches
aft of datum and –8.4 inches left of BL 0Check the helicopter CG envelopes in Figure 8-3 to determine
whether or not the CG is within limits both longitudinally and laterally.
In the longitudinal CG envelope, draw a line vertically
upward from the CG of 94.4 inches aft of datum and a horizontal line from the weight of 2,203 pounds gross weight. These lines cross within the approved area.
In the lateral offset moment envelope, draw a line vertically
upward from the –1,705 lb-in point (on the left side of the horizontal axis) and a line horizontally from 2,203 pounds on the gross weight index. These lines cross within the envelope, showing the lateral balance is also within limits.
Effects of Offloading Passengers an
Using Fuel
Consider the helicopter in Figure 8-4. The first leg of the
flight consumes 26 gallons of fuel, and at the end of this leg, the passenger deplanes. Is the helicopter still within allowable CG limits for takeoff? To find out, make a new chart like the one in Figure 8-5 to show the new loading conditions of the
helicopter at the beginning of the second leg of the flight
Under these conditions, according to the helicopter CG
envelopes in Figure 8-3, both the longitudinal CG and the
lateral offset moment fall outside of the approved area of the envelope. The aircraft longitudinal CG is too far aft and the potential for excessive tail-low attitudes is very high. Under these conditions, it is possible that there will not be enough forward cyclic authority to maintain level flight The helicopter’s lateral offset moment is too far right and may lead to control issues, as well as an increased hazard of dynamic rollover. One possible option to bring the aircraft loading conditions within the approved envelope is to load either ballast or a passenger, as computed in Figure 8-6 and
plotted in Figure 8-3.
8-4Figure 8-6. Determining the longitudinal CG and the lateral offset moment for the second leg of the flight with ballast and/or a different
passenger.Item Weight WeightLongitude
ArmLatitude
ArmLongitude
MomentLongitude
CGLateral Offset
Moment
95.0Helicopter empty weight
Pilot
Ballast/Passenger
Fuel (22 gallons)156,663
12,800
9,600
14,976
194,0391,545
2,027101.4
+2,700−2,025−1,310
−7311,545
2,027+0.2
+13.5
−13.5
−8.4
x x = =Figure 8-5. Determining the longitudinal CG and the lateral offset moment for the second leg of the flight.Item Weight WeightLongitude
ArmLatitude
ArmLongitude
MomentLongitude
CGLateral Offset
Moment
98.2Helicopter empty weight
Pilot
Fuel (22 gallons)156,663
12,80014,976
184,4391,545
1,877101.4
+2,700−1,310+1,6991,545
1,877+0.2
+13.5
−8.4
x x = =Figure 8-4. Determining the longitudinal CG and the lateral offset moment.Item Weight WeightLongitude
ArmLatitude
ArmLongitude
MomentLongitude
CGLateral Offset
Moment
94.4Helicopter empty weight
Pilot
Passenger
Fuel (48 gallons)156,663
12,80010,88027,648
207,9911,545
2,203101.4
+2,700−2,295−2,419−1,7051,545
2,203+0.2
+13.5
−13.5
−8.4
x x = =
Introduction
This chapter discusses general guidelines and procedures for
weighing large fixed-wing aircraft exceeding a takeoff weight of 12,500 pounds. Several examples of center of gravity (CG)
determination for various operational aspects of these aircraft are also included. Persons seeking approval for a weight and balance control program for aircraft operated under Title 14 of the Code of Federal Regulations (14 CFR) part 91, subpart K, 121, 125, or 135 should consult with the Flight Standards District Office (FSDO) or Certificate Management Office (CMO) that has jurisdiction in their area. Additional information on weight and balance for large aircraft can be found in Federal Aviation Administration (FAA) Advisory Circular (AC) 120-27, Aircraft Weight and Balance Control, FAA Type Certificate Data Sheets (TCDS), and the aircraft flight and maintenance manuals for specific aircraf
Weight and Balance Control—
Commuter Category and
Large AircraftChapter 9
9-2Figure 9-1. Determining the distance of CG.Distance CG to LEMAC Datum to CG – Datum to LEMACCG
Distance weight is shifted
=
Figure 9-2. Determining the EWCG in percent MAC.EWCG in % MACCG in inches from LEMAC × 100
MAC=Establishing the Initial Weight of an
Aircraft
Prior to being placed into service, each aircraft is weighed
and the empty weight and CG location established. New aircraft are normally weighed at the factory and are eligible to be placed into operation without reweighing if the weight and balance records were adjusted for alterations and modifications to the aircraft, such as interior reconfigurations
An aircraft transferred from one operator that has an approved
weight and balance program to another operator with an approved program does not need to be weighed prior to use by the receiving operator unless more than 36 calendar months have elapsed since the last individual or fleet weighing, or unless some other modification to the aircraft warrants that the aircraft be weighed. Aircraft transferred, purchased, or leased from an operator without an approved weight and balance program, and that have not been modified or have been minimally modified, can be placed into service without being reweighed if the last weighing was accomplished by an acceptable method (for example, manufacturer’s instructions or AC 43.13-2, Acceptable Methods, Techniques, and Practices—Aircraft Alterations) within the last 12 calendar months and a weight and balance change record was maintained by the operator. It is potentially unsafe to fail to reweigh an aircraft after it has been modified
When weighing large aircraft, compliance with the relevant
manuals, operations specifications, or management specification is required to ensure that weight and balance requirements specified in the Aircraft Flight Manual (AFM) are met in accordance with approved limits. This provides information to the flight crew that allows the maximum payload to be carried safely.
The aircraft should be weighed in still air or an enclosed
building after the aircraft has been cleaned. Ensure that the aircraft is in a configuration for weighing with regard to flight controls, unusable fuel, ballast, oil and other operating fluids, and equipment as required by the controlling weight and balance procedure.
Large aircraft are not usually raised off the floor on jacks
for weighing; they are weighed on ramp-type scales. The scales must be properly calibrated, zeroed, and used in accordance with the manufacturer’s instructions. Each scale should be periodically checked for accuracy as recommended in the manufacturer’s calibration schedule, either by the manufacturer or by a recognized facility, such as a civil department of weights and measures. If no manufacturer’s schedule is available, the period between calibrations should not exceed 12 months.Determining the Empty Weight and
Empty Weight CG (EWCG)
When the aircraft is properly prepared for weighing, roll it onto the scales, and level it. The weights are measured at three weighing points: the two main wheel points and the nosewheel point. The empty weight and empty weight CG (EWCG) are determined by using the following steps with the results recorded in the weight and balance record for use in all future weight and balance computations.
1. Determine the moment index of each of the main-
wheel points by multiplying the net weight (scale reading minus tare weight), in pounds, at these points by the distance from the datum, in inches. Divide these numbers by the appropriate reduction factor.
2. Determine the moment index of the nosewheel
weighing point by multiplying its net weight, in pounds, by its distance from the datum, in inches. Divide this by the reduction factor.
3. Determine the total weight by adding the net weight of
the three weighing points and the total moment index by adding the moment indexes of each point.
4. Divide the total moment index by the total weight and
multiply the result by the reduction factor. This gives the CG in inches from the datum.
5. Determine the distance of the CG behind the leading
edge of the mean aerodynamic chord (LEMAC) by subtracting the distance between the datum and LEMAC from the distance between the datum and the CG. [Figure 9-1]
6. Determine the EWCG in percentage of MAC (percent
MAC) by using the formula in Figure 9-2.
9-3Figure 9-3. Incremental weight changes that should be recorded in a weight and balance change record.In the weight change record of a—
Large cabin aircraftMedium cabin aircraftSmall cabin aircraftAn operator should record any weight changes of—± 10 lb or greater± 5 lb or greater± 1 lb or greater
Figure 9-4. Loading schedule.Item Weight (lb) Moment/1,000
92,837
1,781
16,602
1,020
2,915
10,451
10,451
25,589
161,646BOWPassengers Fwd stationPassengers Aft stationFwd cargoAft cargoFuel tank 1
Fuel tank 3
Fuel tank 2105,500
3,060
16,150
1,5002,500
10,500
10,500
28,000
177,710Documenting Changes to an Aircraft’s
Weight and Balance
The weight and balance system should include methods by
which a complete, current, and continuous record of the weight and CG of each aircraft is maintained, such as a log, ledger, or other equivalent electronic means. Alterations and changes affecting the weight and/or balance of the aircraft should be recorded in this log. Changes in the weight or location of weight in or on the aircraft should be recorded whenever the weight change is at or exceeds the weights listed in Figure 9-3.
Determining the Loaded CG of the
Airplane in Percent MAC
A loading schedule is used to document compliance with the
certificated weight and balance limitations contained in the manufacturer’s AFM and weight and balance manual. The basic operating weight (BOW) and the operating index are entered into a loading schedule like the one in Figure 9-4, and
the variables for a specific flight are entered as appropriate to determine the loaded weight and CG.
Use the data in this example:
Basic operating weight
.................................. 105,500 lb
Basic operating index (total moment/1,000) ....98,837.0
MAC .................................................................. 180.9 in
LEMAC ................................................................. 860.5Figure 9-5 illustrates passenger, cargo, and fuel loading
tables. Using these tables, determine the moment indexes
for the passengers (PAX), cargo, and fuel.
The airplane is loaded in this way:
Passengers (nominal weight—170 pounds each)
Forward compartment ................................................. 18
Aft compartment ......................................................... 95
Cargo
Forward hold ...................................................... 1,500 lb
Aft hold .............................................................. 2,500 lb
Fuel
Tanks 1 and 3 ........................................... 10,500 lb each
Tank 2 .............................................................. 28,000 lb
The formula in Figure 9-6 can be used to determine the
location of the CG in inches aft of the datum.
9-4Figure 9-5. Loading schedule for determining weight and CG.
# of passengers Weight (lb) Moment/1,000
Forward compartment centroid—582.0
Aft compartment centroid—1,028.0 5 850 495
10 1,700 989
15 2,550 1,484
20 3,400 1,979
25 4,250 2,473
29 4,930 2,869
10 1,700 1,748
20 3,400 3,495
30 5,100 5,243
40 6,800 6,990
50 8,500 8,738
60 10,200 10,486
70 11,900 12,233
80 13,600 13,980
90 15,300 15,728
100 17,000 17,476
110 18,700 19,223
120 20,400 20,971
133 22,610 23,243
Weight (lb) Forward hold arm—680.0 Aft hold arm—1,166.0
6,000 6,966
5,000 3,400 5,830
4,000 2,720 4,664
3,000 2,040 3,498
2,000 1,360 2,332
1,000 680 1,166
900 612 1,049
Fuel Loading Table
Weight (lb) Arm Moment/1,000
8,500 992.1 8,433
9,000 993.0 8,937 9,500 993.9 9,442 10,000 994.7 9,947 10,500 995.4 10,451
11,000 996.1 10,957
11,500 996.8 11,463
12,000 997.5 11,970Weight (lb) Arm Moment/1,000
8,500 917.5 7,799
9,000 917.2 8,255 9,500 917.0 8,711 10,000 916.8 9,168 10,500 916.6 9,624 11,000 916.5 10,082
11,500 916.3 10.537
12,000 916.1 10,993Weight (lb) Arm Moment/1,000
22,500 914.5 20,576
23,000 914.5 21,034
23,500 914.4 21,488
24.000 914.3 21,943
24,500 914.3 22,400
25,000 914.2 22,855
25,500 914.2 23,312
26,000 914.1 23,767
26,500 914.1 24,244
27,000 914.0 24,678
27,500 913.9 25,132
28,000 913.9 25,589
28,500 913.8 26,043
29,000 913.7 26,497
29,500 913.7 26,954
30,000 913.6 27,408 Full capacity **(see note at lower left) Tanks 1 and 3 (each) Tank 2 (3 cells)Passenger Loading Table Cargo Loading Table
Moment/1,000
18,500 915.1 16,929
19,000 915.0 17,385
19,500 914.9 17,841
20,000 914.9 18,298
20,500 914.8 18,753
21,000 914.7 19,209
21,500 914.6 19,664
22,000 914.6 20,121** Note:
Computations for Tank 2 weights for 12,500 lb to 18,000 lb have been purposely omitted.
Full capacity
9-5Figure 9-6. Determining the location of the CG in inches aft of
the datum.( ) CG inches aft of datum = × 1,000Total moment index
Total weight
( )= × 1,000161,646
177,710
= 909.6 inches
Figure 9-7. Determining the distance from the CG to the LEMAC.Distance CG to LEMAC = Datum to CG – Datum to LEMAC
= 49.1 inches= 909.6 – 860.5
Figure 9-8. Determining the location of the CG in percent MAC.( ) CG % MAC = × 100Distance CG to LEMAC
MAC
( )= × 10049.1
= 27.1%Determine the distance from the CG to the LEMAC by
subtracting the distance between the datum and LEMAC from the distance between the datum and the CG. [Figure 9-7]
The location of the CG in percent MAC must be known in order to set the stabilizer trim takeoff. [Figure 9-8]
Operational Empty Weight (OEW)
Operational empty weight (OEW) is the basic empty weight or fl et empty weight plus operational items. The operator has two choices for maintaining OEW. The loading schedule may be utilized to compute the operational weight and balance of an individual aircraft, or the operator may choose to establish fleet empty weights for a fleet or group of aircraf
Reestablishing the OEW
The OEW and CG position of each aircraft should be
reestablished at the reweighing. In addition, it should be reestablished through calculation whenever the cumulative change to the weight and balance log is more than plus or minus one-half of 1 percent (0.5 percent) of the maximum landing weight, or whenever the cumulative change in the CG position exceeds one-half of 1 percent (0.5 percent) of the MAC. In the case of rotorcraft and aircraft that do not have a MAC-based CG envelope (e.g., canard equipped airplane), whenever the cumulative change in the CG position exceeds one-half of 1 percent (0.5 percent) of the total CG range, the weight and balance should be reestablished.
When reestablishing the aircraft OEW between reweighing
periods, the weight changes may be computed provided the weight and CG location of the modifications are known; otherwise, the aircraft must be reweighed.
Fleet Operating Empty Weights (FOEW)
An operator may choose to use one weight for a fleet or group
of aircraft if the weight and CG of each aircraft is within the limits stated above for establishment of OEW. When the cumulative changes to an aircraft weight and balance log exceed the weight or CG limits for the established fleet weight, the empty weight for that aircraft should be reestablished. This may be done by moving the aircraft to another group, or reestablishing new fleet operating empty weights (FOEWs)
Onboard Aircraft Weighing System
Some large transport airplanes have an onboard aircraft
weighing system (OBAWS) that, when the aircraft is on the ground, gives the flight crew a continuous indication of the aircraft total weight and the location of the CG in percent MAC. Procedures are required to ensure the onboard weight and balance system equipment is periodically calibrated in accordance with the manufacturer’s instructions.
An operator may use an onboard weight and balance
system to measure an aircraft’s weight and balance as a primary means to dispatch an aircraft, provided the FAA has certified the system and approved the system for use in an operator’s weight and balance control program. As part of the approval process, the onboard weight and balance system must maintain its certificated accuracy. The accuracy demonstration test is provided in the maintenance manual portion of the Supplemental Type Certificate (STC) or type certificate of the onboard weight and balance system.
The system consists of strain-sensing transducers in each
main wheel and nosewheel axle, a weight and balance computer, and indicators that show the gross weight, the CG location in percent MAC, and an indicator of the ground attitude of the aircraft.
The strain sensors measure the amount each axle defl cts and
sends this data into the computer, where signals from all of the transducers and the ground attitude sensor are integrated. The results are displayed on the indicators for the flight crew. Using an onboard weight and balance system does not relieve an operator from the requirement to complete and maintain a load manifest.
9-6Figure 9-9. Stabilizer trim setting in ANU units.Stabilizer Trim Setting—Units Airplane Nose Up
101214161820222426283032
3/4
71/2
63/4
61/4
53/4
51/2
41/2
31/2
21/2Flaps (all) CGFigure 9-10. Determining the distance from CG to the LEMAC.Distance CG to LEMAC = Datum to CG – Datum to LEMAC
= 10.7 inches= 635.7 – 625
Figure 9-11. Determining the location of CG in percent MAC.( ) CG in % MAC = × 100Distance CG to LEMAC
MAC
( )= × 10010.7
= 8.0 % MAC
Figure 9-12. Determining the location of CG in inches before cargo
is removed.( ) CG (inches aft of LEMAC) = × MACCG in % MAC
( )= × 141.522.5
= 31.84 inchesDetermining the Correct Stabilizer Trim Setting
It is important before takeoff to set the stabilizer trim for the
existing CG location. There are two ways the stabilizer trim setting systems may be calibrated: in percent MAC and in units airplane nose up (ANU).
If the stabilizer trim is calibrated in percent MAC, determine
the CG location in percent MAC as has just been described, then set the stabilizer trim on the percentage figure thus determined. Some aircraft give the stabilizer trim setting in units of ANU that correspond with the location of the CG in percent MAC. When preparing for takeoff in an aircraft equipped with this system, first determine the CG in percent MAC in the way described above, then refer to the stabilizer trim setting chart on the takeoff performance page of the pertinent AFM. Figure 9-9 is an excerpt from the AFM chart
on the takeoff performance of a Boeing 737.
Consider an airplane with these specifications
CG location
................................................ station 635.7
LEMAC ........................................................ station 625
MAC .................................................................. 134.0 in
1. Determine the distance from the CG to the LEMAC
by using the formula in Figure 9-10.
2. Determine the location of the CG in percent MAC by
using the formula found in Figure 9-11.
Refer to Figure 9-9 for all flap settings and a CG located
at 8 percent MAC; the stabilizer setting is 73⁄4 units ANU.Determining CG Changes Caused by
Modifying the Cargo
Since large aircraft can carry substantial cargo, adding,
subtracting, or moving any of the cargo from one hold to another can cause large shifts in the CG.
Effects of Loading or Offloading Cargo
Both the weight and CG of an aircraft are changed when
cargo is loaded or offloaded. In the following example, the new weight and CG are calculated after 2,500 pounds of cargo is offloaded from the forward cargo hold
Aircraft specifications are
Loaded weight
................................................. 90,000 lb
Loaded CG ........................................ 22.5 percent MAC
Weight change ................................................... 2,500 lb
Forward cargo hold centroid ...................... station 352.1
MAC .................................................................. 141.5 in
LEMAC ................................................... station 549.13
1. Determine the CG location in inches from the
datum before the cargo is removed. Do this by first
determining the distance of the CG aft of the LEMAC. [Figure 9-12]
9-7Figure 9-13. Determining the distance between CG and the datum.CG (inches from datum) = CG inches aft of LEMAC
+ Datum to LEMAC
= 580.97 inches= 31.84 + 549.13
Figure 9-14. Determining the moment/1,000 for the original weight.Moment/1,000 =Weight × Arm
1,000
90,000 × 580.97
1,000
= 52,287.3=
Figure 9-15. Determining the moment/1,000 of the removed weight.Moment/1,000 =Weight × Arm
1,000
2,500 × 352.1
1,000
= 880.25=
Figure 9-16. New weights and CG.Weight (lb) Moment/1,000 CG (inches from datum) CG (percent MAC)
27.12Original data
ChangesNew data90,000
– 2,500
87,50052,287.3
51,407.0Figure 9-17. Determining the location of new CG.CG = × 1,000Total moment/1,000
Total weight
51,407.0
87,500= × 1,000
= 587.51 inches behind the datum
Figure 9-18. Determining the distance between the CG and LEMAC.CG (inches aft of LEMAC) =
CG (inches from datum) – LEMAC
= 38.38 inches= 587.51 – 549.13
Figure 9-19. Determining the new CG in percent MAC.( ) CG % MAC = × 100Distance CG to LEMA
MAC
( )= × 10038.38
= 27.12% MAC2. Determine the distance between the CG and the datum
by adding the CG in inches aft of LEMAC to the
distance from the datum to LEMAC. [Figure 9-13]
3. Determine the moment/1,000 for the original weight.
[Figure 9-14]
4. Determine the new weight and new CG by first
determining the moment/1,000 of the removed weight. Multiply the weight removed (2,500 pounds) by the centroid of the forward cargo hold (352.1 inches), and then divide the result by 1,000. [Figure 9-15]
5. Subtract the removed weight from the original weight
and subtract the moment/1,000 of the removed weight from the original moment/1,000. [Figure 9-16]6. Determine the location of the new CG by dividing
the total moment/1,000 by the total weight and multiplying this by the reduction factor of 1,000. [Figure 9-17]
7. Convert the new CG location to percent MAC. First,
determine the distance between the CG location and LEMAC. [Figure 9-18]
8. Then, determine the new CG in percent MAC.
[Figure 9-19]
Loading 3,000 pounds of cargo into the forward cargo hold moves the CG forward 5.51 inches, from 27.12 percent MAC to 21.59 percent MAC.
9-8Figure 9-24. Determining the change in CG caused by shifting
2,500 pounds of cargo.CG = × 100Weight shifted × Distance shifted
Total weight
=2,500 × (227.9 + 144.9)
90,000
=2,500 × 372.8
90,000
=10.36 inchesFigure 9-21. Determining the new CG after shifting cargo weight.New CG = Old CG ± CG
= 591.33 inches= 580.97 + 10.36Figure 9-22. Converting the location of CG to percent MAC.( ) CG % MAC = × 100CG inches
MAC
( )= × 10010.36
= 7.32% MAC
Figure 9-23. Determining the new CG in percent MAC.New CG % MAC = Old CG ± CG
= 29.82% MAC= 22.5% + 7.32%
Figure 9-20. Calculating the change in CG, using index arms.CG = Weight shifted × Distance shifted
Total weight
=2,500 × (724.9 – 352)
90,000
=2,500 × 372.9
90,000
=10.36 inchesEffects of Shifting Cargo From One Hold to
Another
When cargo is shifted from one cargo hold to another, the CG
changes, but the total weight of the aircraft remains the same.
For example, use the following data:
Loaded weight ................................................ 90,000 lb
Loaded CG ............. station 580.97 (22.5 percent MAC)
Forward cargo hold centroid ........................ station 352
Aft cargo hold centroid ............................. station 724.9
MAC .................................................................. 141.5 in
LEMAC ....................................................... station 549
To determine the change in CG ( ΔCG) caused by shifting
2,500 pounds of cargo from the forward cargo hold to the
aft cargo hold, use the formula in Figure 9-20.
Since the weight was shifted aft, the CG moved aft and the CG change is positive. If the shift were forward, the CG change would be negative.
Before the cargo was shifted, the CG was located at station
580.97, which is 22.5 percent of MAC. The CG moved aft 10.36 inches, so the new CG is found using the formula from Figure 9-21.
Convert the location of the CG in inches aft of the datum to
percent MAC by using the formula in Figure 9-22.
The new CG in percent MAC caused by shifting the cargo is the sum of the old CG plus the change in CG. [Figure 9-23]Some AFMs locate the CG relative to an index point rather than the datum or the MAC. An index point is a location specified by the aircraft manufacturer from which arms used in weight and balance computations are measured. Arms measured from the index point are called index arms, and objects ahead of the index point have negative index arms, while those behind the index point have positive index arms.
Use the same data as in the previous example, except for
these changes:
Loaded CG
.......................... index arm of 0.97, which is
22.5 percent of MAC
Index point ................................... fuselage station 580.0
Forward cargo hold centroid ............... –227.9 index arm
Aft cargo hold centroid ....................... +144.9 index arm
MAC .................................................................. 141.5 in
LEMAC .............................................. –30.87 index arm
The weight was shifted 372.8 inches (–227.9 + Δ = +144.9, Δ =372.8).
The change in CG can be calculated by using this formula
found in Figure 9-24.
9-9Figure 9-25. Determining the new CG, moved aft 10.36 inches.New CG = Old CG ± CG
= 11.33 index arm= 0.97 + 10.36
Figure 9-26. The change in the CG in percent MAC.New CG % MAC = Old CG ± CG
= 29.82% MAC= 22.5% + 7.32%
Figure 9-27. The new CG in percent MAC.( ) CG % MAC = × 100CG inches
MAC
( )= × 10010.36
= 7.32% MAC
Figure 9-28. Determining pallet area in square feet.Area (sq. ft.) = Length (inches) × Width (inches)
144 square inches/square foot
=48.5 × 33.5
=1,624.7
=11.28 square feetSince the weight was shifted aft, the CG moved aft, and the
CG change is positive. If the shift were forward, the CG change would be negative. Before the cargo was shifted, the CG was located at 0.97 index arm, which is 22.5 percent MAC. The CG moved aft 10.36 inches, and the new CG is shown using the formula in Figure 9-25.
The change in the CG in percent MAC is determined by using the formula in Figure 9-26.
The new CG in percent MAC is the sum of the old CG plus the change in CG. [Figure 9-27]
Notice that the new CG is in the same location whether the distances are measured from the datum or from the index point.
Determining Cargo Pallet Loads and Floor
Loading Limits
Each cargo hold has a structural floor loading limit based on
the weight of the load and the area over which this weight is distributed. To determine the maximum weight of a loaded cargo pallet that can be carried in a cargo hold, divide its total weight, which includes the weight of the empty pallet and its tie down devices, by its area in square feet. This load per square foot must be equal to or less than the floor load limit.In this example, determine the maximum load that can be placed on this pallet without exceeding the floor loading limit.
Pallet dimensions
.......................................... 36 by 48 in
Empty pallet weight ................................................ 47 lb
Tie down devices .................................................... 33 lb
Floor load limit ............................ 169 lb per square foot
The pallet has an area of 36 inches (3 feet) by 48 inches
(4 feet), which equals 12 square feet, and the floor has a
load limit of 169 pounds per square foot. Therefore, the total weight of the loaded pallet can be 169 × 12 = 2,028 pounds. Subtracting the weight of the pallet and the tie down devices gives an allowable load of 1,948 pounds (2,028 – [47 + 33]).
Determine the floor loading limit that is needed to carry a
loaded cargo pallet having the following dimensions and weights:
Pallet dimensions
................................... 48.5 by 33.5 in
Pallet weight .......................................................... 44 lb
Tiedown devices .................................................... 27 lb
Cargo weight ..................................................... 786.5 lb
First, determine the number of square feet of pallet area as
shown in Figure 9-28.
Then, determine the total weight of the loaded pallet:
Pallet .................................................................... 44.0 lb
Tiedown devices ................................................. 27.0 lb
Cargo ................................................................. 786.5 lb
Total ................................................................... 857.5 lb
Determine the load imposed on the floor by the loaded pallet. [Figure 9-29] The floor must have a minimum loading limit
of 76 pounds per square foot.
9-10Figure 9-29. Determining the load imposed on the floor by the
loaded pallet.Floor Load =Loaded weight
Pallet area
= 76.0 pounds/square foot=
Figure 9-30. Finding the maximum takeoff weight.Max limit
142,000
184,200Landing weight
+ trip fuel
Takeoff weightTrip limit
142,000
+ 40,000
182,000
Figure 9-31. Determining zero fuel weight with lower trip limits.Max limit
184,200138,000Landing weight
– fuel load
Zero fuel weightTrip limit
182,000
– 54,000
128,000Figure 9-32. Finding maximum payload with lower trip limits.Max limit
138,000 Zero fuel weight
– BOW
Payload (pounds)Trip limit
128,000
–100,500
27,500
Determining the Maximum Amount of Payload
That Can Be Carried
The primary function of a transport or cargo aircraft is to carry
payload, which is the portion of the useful load, passengers, or cargo that produces revenue. To determine the maximum amount of payload that can be carried, both the maximum limits for the aircraft and the trip limits imposed by the particular trip must be considered. In each of the following steps, the trip limit must be less than the maximum limit. If it is not, the maximum limit must be used.
These are the specifications for the aircraft in this example
Basic operating weight (BOW)
..................... 100,500 lb
Maximum zero fuel weight ............................ 138,000 lb
Maximum landing weight .............................. 142,000 lb
Maximum takeoff weight .............................. 184,200 lb
Fuel tank load ................................................. 54,000 lb
Estimated fuel burn en route ............................ 40,000 lb
1. Compute the maximum takeoff weight for this trip.
This is the maximum landing weight plus the trip fuel.
[Figure 9-30]
2. The trip limit is lower than the maximum takeoff
weight, so it is used to determine the zero fuel weight. [Figure 9-31]3. The trip limit is again lower than the maximum takeoff
weight, so use it to compute the maximum payload for this trip. [Figure 9-32]
Under these conditions, 27,500 pounds of payload may be carried.
Determining the Landing Weight
It is important to know the landing weight of the aircraft in
order to set up the landing parameters and to be certain the aircraft is able to land safely at the intended destination.
In this example of a four-engine turboprop airplane,
determine the airplane weight at the end of 4.0 hours of cruise under these conditions:
Takeoff weight
............................................... 140,000 lb
Pressure altitude during cruise .......................... 16,000 ft
Ambient temperature during cruise ..................... –32 °C
Fuel burned during descent and landing ............ 1,350 lb
Refer to the U.S. Standard Atmosphere Table in Figure 9-33 and the gross weight table in Figure 9-34 when
completing the following steps:
1. Use the U.S. Standard Atmosphere Table to
determine the standard temperature for 16,000 feet
(–16.7 °C).
2. The ambient temperature is –32 °C, which is a
deviation from standard of 15.3 °C. (–32° – (–16.7°) = –15.3°). It is below standard.
3. In the gross weight table, follow the vertical line
representing 140,000 pounds gross weight upward until it intersects the diagonal line for 16,000 feet pressure altitude.
4. From this intersection, draw a horizontal line to the left
to the temperature deviation index (0 °C deviation).
5. Draw a diagonal line parallel to the dashed lines for
Below Standard from the intersection of the horizontal line and the Temperature Deviation Index.
6. Draw a vertical line upward from the 15.3 °C
Temperature Deviation From Standard.
9-11Figure 9-33. Standard atmosphere table.Feet inHg mmHg PSI °C °F
2,000
4,0006,0008,000
10,000
12,000
14,00016,00018,00020,000
22,000
24,00026,00028,00030,000
32,000
34,00036,00038,00040,000
42,000
44,00046,00048,00050,000
55,000
60,00029.9227.8225.8423.9822.2320.58
17.5816.2214.9513.76
7.406.736.125.56
4.594.173.793.44
2.14760.0706.7656.3609.1564.6522.7
446.5412.0379.7349.5
294.9270.3237.4226.1
188.0171.0155.5141.2
13.6612.6911.7810.9210.11
9.358.637.967.346.75
5.705.224.784.37
3.633.302.992.72
2.242.021.851.68
−0.8−0.4
−8.8
−12.7
−16.7−20.7−24.6
−28.6
−32.5−36.5−40.4−44.4
−48.4
−52.4−56.3−56.5−56.5
−56.5
−56.5−56.5−56.5−56.559.051.944.737.630.523.3
−5.2
−12.3
−19.5
−26.6−33.7−40.9−48.0
−55.1
−62.3−69.4−69.7−69.7
−69.7
−69.7−69.7−69.7−69.7
Temperature
remains constantFigure 9-35. Determining the total fuel burn for a 4-hour cruise.Total fuel burn =
Lb/hr/engine × No. engines × Hours flight duration
= 18,160 pounds= 1,135 × 4 × 4
Figure 9-34. Gross weight table.Fuel flow—100 lb per hour per engine
Moment of the loaded aeroplane (lb in x 100)
20 15.3 10 0 80 90 100 110 120 130 140 150 160 170 18016
11.35Pressure altitude—1,000 feet
SL
36322824TT limit
Gross weight—1,000 lb7. Draw a horizontal line to the left from the intersection
of the Below Standard diagonal and the 15.3 °C
temperature deviation vertical line. This line crosses
the fuel flow–100 pounds per hour per engine index at 11.35 and indicates that each of the four engines burns 1,135 (100 × 11.35) pounds of fuel per hour. The total fuel burn for the 4-hour cruise is shown in Figure 9-35.
The airplane gross weight was 140,000 pounds at takeoff with 18,160 pounds of fuel burned during cruise and 1,350 pounds burned during the approach and landing phase. This leaves a landing weight of 140,000 – (18,160 + 1,350) = 120,490 pounds.
9-12Figure 9-36. Determining the amount of weight the aircraft must
lose to reach the maximum allowable landing weight. 171,000 lb cruise weight
– 142,500 lb maximum landing weight 28,500 lb required reduction
Figure 9-37. Determining the amount of fuel burned from the
beginning of the dump to touchdown.Fuel flow =3,170 lb/hr/engine
= 52.83 lb/min engineFigure 9-38. Determining the amount of fuel needed to dump. 28,500.00 lb required weight reduction – 2,007.54 lb fuel burned after start of dumping 26,492.46 lb fuel to be dumped
Figure 9-39. Determine the time needed to dump fuel.= 11.52 minutes26,492.46
2,300Determining Fuel Dump Time in Minutes
Most large aircraft are approved for a greater weight for
takeoff than for landing. To make it possible for them to return to landing soon after takeoff, a fuel jettison system is sometimes installed. It is important in an emergency situation that the flight crew be able to dump enough fuel to lower the weight to its allowed landing weight. This is done by timing the dumping process.
In this example, the aircraft has two engines operating and
these specifications apply
Cruise weight
................................................. 171,000 lb
Maximum landing weight .............................. 142,500 lb
Time from start of dump to landing .............. 19 minutes
Average fuel flow during
Dumping and descent ............................. 3,170 lb/hr/eng
Fuel dump rate ....................................... 2,300 lb/minute
To calculate the fuel dump time in minutes:
1. Determine the amount of weight the aircraft must
lose to reach the maximum allowable landing weight. [Figure 9-36]
2. Determine the amount of fuel burned from the
beginning of the dump to touchdown. [Figure 9-37]For both engines, this is 52.83 × 2 = 105.66 lb/minute.
The engines burn 105.66 lbs of fuel per min for 19 minutes
(the duration of the dump), which calculates to 2007.54 pounds of fuel burned between the beginning of the dump and touchdown.
3. Determine the amount of fuel needed to dump by
subtracting the amount of fuel burned during the dump from the required weight reduction. [Figure 9-38]
4. Determine the time needed to dump this amount of
fuel by dividing the number of pounds of fuel to dump by the dump rate. [Figure 9-39]
Weight and Balance of Commuter Category
Airplanes
The Beech 1900 is a typical commuter category airplane that
can be configured to carry passengers or cargo. Figure 9-40
shows the loading data of this type of airplane in the passenger configuration
Determining the Loaded Weight and CG
As this airplane is prepared for flight, a manifest is prepared.
[Figure 9-41]
9-13Figure 9-40. Loading data for passenger configuration.
Row 1 F.S. 210Crew F .S. 129Fwd. press BHD F .S. 84.0
Aft press BHD F .S. 557.5Row 2 F.S. 230
Row 3 F.S. 260
Row 4 F.S. 290
Row 5 F.S. 320
Row 6 F.S. 350
Row 7 F.S. 380
Row 8 F.S. 410
Row 9 F.S. 440Loading Data Standard Seating
F.S. 456.0
F.S. 509.5F.S. 150.6F.S. 43.0
F.S. 5177.35
F.S. 513.5F.S. 453.5F.S. 175.6F.S. 150.6Aft baggage/cargo compt. (Aft section)
Aft baggage/cargo compt. (F wd. sec tion)
Aft partition
Baggage webFwd. cabin baggage compt .
Nose baggage compt.
Baggage/cargo location Maximum Weight Ar m
Nose baggage compa rtment ................... ............................................150....................................................................................................65.5
Forward cabin baggage compa rtment. 250................................. 163.5
(includes up to 100 pounds that may be
suspended from clothes rod)Aft baggage/cargo compa rtment F wd. sec tion ...................880....................................................................................................483.5
Aft section.......................630....................................................................................................533.0
Note
For compa rtment loading that results in only pa rtial utilization of total compar tment volume, load items must be
distributed or secured in a manner that precludes shifting under normally anticipated operating condition s.
Figure 9-41. Determining the loaded weight and CG of a Beech 1900 in the passenger configuration.Item Weight Arm Moment/100 CG
25,823
1,190
3,198
7,866
43,139 292.9Airplane basic EW
CrewPassengers Row 1 Row 2 Row 3 Row 4 Row 5 Row 6 Row 7 Row 8 Row 9Baggage Nose Forward cabin Aft (forward section) Aft (aft section)Fuel jet A @ +25 °C 390 gallons 9,226
250190170190340190
2,633
14,729129
230260290320350380410440
163.6483.5533.0
9-14Figure 9-42. Weight and moments—occupants.Weight
Moment/100
220230240250103116129
284297310323160180200
440460480500184207230
506529552575208234260
572598624650232261290
638667696725256288320
704736768800280315350
770805840875304342380
836874912950328369410
1025352396440
Useful Load Weights and Moments—Occupants
Crew Cabin seats
F.S.
129F.S.
200F.S.
230F.S.
260F.S.
290F.S.
320F.S.
350F.S.
380F.S.
410F.S.
Figure 9-43. Weight and moments—baggage.Weight
102030405060708090
1001502002503003504004505005506006306507007508008508807
13202633394652596698163349658298
1151311471642453274094897
145193242290338387435484725967
12091450169219342176241826592901304631433384362638684110425553
107160213266320373426480533800
1066133215991866213223982665293231983358
Moment/100Useful Load Weights and Moments—Baggage
Nose
baggage
compartment
F.S. 65.5Forward
cabin
baggage
compartment
F.S. 163.6AFT baggage/
cargo
compartment
(Forward
section)
F.S. 483.5AFT baggage/
cargo
compartment
(Aft
section)
F.S. 533.0
Figure 9-44. Density variation of aviation fuel.−40 −30 −20 −10 0 10 20 30 407.5
5.5Aviation kerosene jet A & Jet A1
Jet B (JP-4)
Aviation gasoline grade 100/130NOTE: The fuel quantity indicator
is calibrated for correct indication when using aviation kerosene jet A and jet A1. When using other fuels, multiply the indicated fuel quantity in pounds by 0.99 for jet B (JP-4) or by aviation gasoline (100/130) to obtain actual fuel quantity in pounds.Aviation
kerosene Jet A and Jet A1 0.812
Jet B (JP-4) 0.785AV gas grade
100/130 0.703Average specificgravityat 15 °C (59 °F)Fuel Specific weight (lb/US gal)
Temperature (°C) 1. The crew weight and the weight of each passenger is
entered into the manifest. The moment/100 for each
occupant is determined by multiplying the weight by the arm and dividing by 100. This data is available in the AFM and is shown in the Weight and Moments— Occupants table. [Figure 9-42]
2. The weight of the baggage in each compartment used
is entered with its moment/100. This is determined in the Weights and Moments—Baggage table. [Figure 9-43]3. Determine the weight of the fuel. Jet A fuel has
a nominal specific gravity at +15 °C of 0.812
and weighs 6.8 pounds per gallon, but at +25 °C,
according to the Density Variation of Aviation Fuel Chart [Figure 9-44], it weighs 6.75 lb/gal. Using this
9-15Figure 9-45. Weights and moments—usable fuel.Gallons
Weight Moment
1006.5 lb/gal
Weight Moment
1006.6 lb/gal
Weight Moment
1006.7 lb/gal
Weight Moment
1006.8 lb/gal
2030405060708090
100110120130140150160170180190
210220230240250260270280290
310320330340350360370380390
130195260325390455520585
715780845910975
1,0401,1061,1701,235
1,300
1,3651,4301,4951,5601,6251,6901,7551,8201,885
1,950
2,0152,0802,1452,2102,2752,3402,4052,4702,535
2,600
2,6652,7302,763197394592789987
1,1851,3831,5811,779
1,977
2,1752,3722,5692,7652,9623,1573,3513,5453,739
3,932
4,1244,3154,5074,6984,8895,0805,2715,4625,651
5,842
6,0326,2256,4176,6106,8026,9957,1887,3817,575
7,768
7,9628,1568,25966
132198264330396462528594
726792858924990
1,0561,1221,1881,254
1,320
1,3861,4521,5181,5841,6501,7161,7821,8481,914
1,980
2,0462,1121,2782,2442,3102,3762,4422,5082,574
2,640
2,7062,7722,805200401601802
1,0021,2031,4041,6051,806
2,007
2,2082,4092,6082,8083,0073,2053,4033,6003,797
3,992
4,1874,3824,5764,7704,9645,1585,3525,5465,738
5,932
6,1256,3216,5166,7116,9077,1037,2997,4957,691
7,888
8,0858,2828,38667
134201268335402469536603
1,0051,0721,1391,2061,273
1,340
1,4071,4741,5411,6081,6751,7421,8091,8761,943
2,010
2,0772,1442,2112,2782,3452,4122,4792,5462,613
2,680
2,7472,8142,848203407610814
1,0181,2221,4261,6301,834
2,038
2,2422,4452,6482,8503,0533,2543,4543,6543,854
4,053
4,2504,4484,6464,8435,0405,2365,4335,6305,825
6,022
6,2186,4166,6156,8137,0117,2107,4097,6097,808
8,007
8,2078,4078,51368
136204272340408476544612
1,0201,0881,1561,2241,292
1,360
1,4281,4961,5641,6321,7001,7681,8361,9041,972
2,040
2,1082,1762,2442,3122,3802,4482,5162,5842,652
2,720
2,7882,8562,890206413619826
1,0331,2401,4471,6541,861
2,068
2,2752,4822,6872,8933,0993,3033,5063,7093,912
4,113
4,3144,5144,7154,9155,1155,3155,5145,7145,912
6,112
6,3116,5126,7136,9157,1167,3187,5207,7227,924
8,127
8,3308,5328,640Useful Load Weights and Moments—Usable Fuel
chart, determine the weights and moment/100 for 390
gallons of Jet A fuel by interpolating between those
for 6.7 lb/gal and 6.8 lb/gal. The 390 gallons of fuel at this temperature weighs 2,633 pounds, and its moment index is 7,866 lb-in/100.
4. Add all of the weights and all of the moment indexes.
Divide the total moment index by the total weight, and multiply this by the reduction factor of 100. The total weight is 14,729 pounds; the total moment index is 43,139 lb-in/100. The CG is located at fuselage station 292.9. [Figure 9-45]5. Check to determine that the CG is within limits for
this weight. Refer to the Weight and Balance Diagram. [Figure 9-46] Draw a horizontal line across the envelope at 14,729 pounds of weight and a vertical line from the CG of 292.9 inches aft of the datum. These lines cross inside the envelope, verifying the CG is within limits for this weight.
9-16Figure 9-46. Weight and balance diagram.17,000
16,000
15,000
14,00013,000
12,000
11,00010,000
9,000
272 276 280 284 288 292 296 300 304
CG (inches aft of datum)
Weight (lb)Maximum zero fuel weight
Maximum takeoff weight 16,600
Maximum landing weight 16,000Maximum zero fuel weight 14,000Maximum takeoff weight
Determining the Changes in CG When Passengers Are Shifted
Using the loaded weight and CG of the Beech 1900, calculate
the change in CG when the passengers in rows 1 and 2 are moved to rows 8 and 9. [Figure 9-47] Note that there is no
weight change, but the moment index has been increased by 1,155 pound-inches/100 to 44,294. The new CG is at fuselage station 300.7. [Figure 9-48]This type of problem is usually solved by using the following two formulas. The total amount of weight shifted is 550 pounds (300 + 250) and both rows of passengers have moved aft by 210 inches (410 – 200 and 440 – 230). The CG has been shifted aft by 7.8 inches, and the new CG is at station 300.7. [Figure 9-49]
9-17Figure 9-47. Changes in CG caused by shifting passenger seats.Item Weight Arm Moment/100 CG
(−) 600
(−) 575
(+) 1,230(+) 1,100
43,139
(+) 1,155
44,294 300.7 Row 1 Row 2 Row 8 Row 9
Original conditions
ChangesNew conditions(−) 300(−) 250
(+) 300
(+) 250
14,729
14,729200230
Figure 9-48. Determining the new CG at fuselage station.( ) CG = × 10043,139 + 1,155
14,729
= 300.7
Figure 9-49. Determining the new CG at station after CG has
shifted aft.CG =Weight shifted × Distance shifted
Total weight
=550 × 210
14,729
= 7.8 inches
= 292.9 + 7.8CG = Original CG + CG
= 300.7 inches aft of datum
Figure 9-50. One passenger configuration of a B737-800.
Mixed class:
12 first class seats at 36-inch pitch
148 economy class seats at 32-inch pitchG
C
CGAAG
LG
AALAIn a large cabin aircraft with high-density seating such as
the B737-800, the operator must account for the seating of
passengers in the cabin [Figure 9-50]. If assigned seating
is used to determine passenger location, the operator must implement procedures to ensure the assignment of passenger seating is incorporated into the loading procedure. It is recommended that the operator take into account the possibility that some passengers may not sit in their assigned seats. If the actual seating location of each passenger is not known, the operator may assume that all passengers are seated uniformly throughout the cabin or a specified subsection of the cabin. Reasonable assumptions can be made about the manner in which people distribute themselves throughout the cabin. For example, window seats are occupied first followed by aisle seats, followed by the remaining seats (window-aisle-remaining seating). Both forward and rear loading conditions should be considered. The passengers may fill up the window, aisle, and remaining seats from the front of the aircraft to the back, or the back to the front. If necessary, the operator may divide the passenger cabin into subsections or zones and manage the loading of each zone individually. It can be assumed that passengers will be sitting uniformly throughout each zone.
Another consideration is the inflight movement of passengers,
crew, and equipment. It is assumed that all passengers, crew, and equipment are secured when the aircraft is in the takeoff or landing configuration. Standard operating procedures
9-18Figure 9-51. Loading data for cargo configuration.
Section A
Section B
Section C
Section D
Section E
Section F
Section G
Section H
Section I
Section KSec
JF.S. 210
F.S. 240
F.S. 270
F.S. 300
F.S. 330
F.S. 360
F.S. 390
F.S. 420
F.S. 480
F.S. 513.5F.S. 450A 600 F.S. 225.0
B 600 F.S. 255.0C 600 F.S. 285.0D 600 F.S. 315.0E 600 F.S. 345.0F 600 F.S. 375.0G 600 F.S. 405.0H 600 F.S. 435.0I 600 F.S. 465.0J 250 F.S. 499.5K 565 F.S. 533.0Section
Notes:
1. All cargo in sections A through J must be supported on the seat tracks and secured to the seat tracks and side seat rails by an FAA-approved system.
2. Concentrated cargo loads
in sections A through L must not exceed 100 lb per square foot.
3. Cargo in sections K and L
must be retained by baggage webs and partitions provided as part of standard airplane.
4. Any exception to the
above procedures
requires approval by a local FAA office. Centroid
armMaximum
structural
capacity
Loading cargo configurationshould be taken into account. Examples of items that can
move during flight are:
• Flight deck crew members moving to the lavatory.
• Flight attendants moving throughout the cabin.
• Service carts moving throughout the cabin.
• Passengers moving throughout the cabin.
• Passengers moving to the lavatory.
Determining Changes in Weight and CG
When the Aircraft Is Operated in Its Cargo
Configuratio
To determine changes in weight and CG when the aircraft
is operated in its cargo configuration, the Beech 1900 is used as an example. Figure 9-51 illustrates the airplane
configuration. Notice that the arm of each cargo section is the centroid of that section. The flight manifest of the Beech 1900 in the cargo confi uration is illustrated in Figure 9-52 . The BOW includes
the pilots and their baggage and there is no separate item for them.
At the standard temperature of 15 °C, the fuel weighs 6.8
pounds per gallon. Refer to Figure 9-45 to determine the
weight and moment index of 370 gallons of Jet A fuel. The CG under these loading conditions is located at station 296.2.
Determining the CG Shift When Cargo Is Moved
From One Section to Another
To calculate the CG when cargo is shifted from one section
to another, use the formula found in Figure 9-53 . If the cargo
is moved forward, the CG is subtracted from the original CG. If the cargo is shifted aft, add the CG to the original.
Determining the CG Shift When Cargo Is Added
or Removed
To calculate the CG when cargo is added or removed, add or
subtract the weight and moment index of the affected cargo to the original loading chart. Determine the new CG by dividing the new moment index by the new total weight, and multiply this by the reduction factor. [Figure 9-54]
Determining Which Limits Are Exceeded
When preparing an aircraft for flight, consider all parameters and check to determine that no limits have been exceeded. Consider the parameters below, and determine which limit, if any, has been exceeded.
• The aircraft in this example has a basic empty weight
of 9,005 pounds and a moment index of 25,934 pound inches/100.• The crew weight is 340 pounds and its moment/100
is 439.
• The passengers and baggage have a weight of 3,950
pounds and a moment/100 of 13,221.
• The fuel is computed at 6.8 lb/gal. The ramp load is
340 gallons or 2,312 pounds. Fuel used for start and taxi is 20 gallons, or 136 pounds. Fuel remaining at landing is 100 gallons, or 680 pounds.
• Maximum takeoff weight is 16,600 pounds.
• Maximum zero fuel weight is 14,000 pounds.
• Maximum landing weight is 16,000 pounds.
9-19Figure 9-53. Shifting cargo from one section to another. CG = Weight shifted x Distance shifted
Total weightFigure 9-52. Flight manifest of a Beech 1900 in the cargo configuration.Item Weight Arm Moment/100 CG
25,934
1,020
1,2831,890
2,070
2,250
7,520
43,452 296.2BOWCargo section A
Cargo section B
Cargo section CCargo section D
Cargo section E
Cargo section FCargo section GCargo section HCargo section ICargo section JCargo section KFuel jet A at +15 °C gallons 3709,005
2,516
14,671225.0
375.0405.0435.0465.0499.5533.0
Figure 9-54. Determining the new CG by dividing the new moment
index by the new total weight, multiplied by the reduction factor. CG = x Reduction factor Total moment index
Total weight
Figure 9-55. Determining the zero fuel weight.Item Weight (lb) Moment CG
Basic empty weightCrewPassengers & baggageZero fuel weight9,005
3,950
13,29525,934
13,22139,594Figure 9-56. Determining the takeoff weight and CG.Item Weight (lb) Moment CG
Zero fuel weightTakeoff fuel 320 galRamp load−fuel for
start & taxi
340 − 20 = 320 gal
Takeoff weight13,295
2,176
15,47139,594
6,512
46,106 298.0
Figure 9-57. Determining the landing weight and CG.Item Weight (lb) Moment CG
Zero fuel weightFuel at landing 100 galLanding weight13,295
13,97539,594
1,977
41,571 297.5Take these steps to determine which limit, if any, is exceeded:
1. Determine the zero fuel weight, which is the weight
of the aircraft with all of the useful load except the
fuel onboard. [Figure 9-55]
The zero fuel weight of 13,295 pounds is less than
the maximum of 14,000 pounds, so this parameter is acceptable.
2. Determine the takeoff weight and CG. The takeoff
weight is the zero fuel weight plus the weight of the ramp load of fuel, minus the weight of the fuel used for start and taxi. The takeoff CG is the moment/100 divided by the weight, and then the result multiplied by 100. The takeoff weight of 15,471 pounds is below the maximum takeoff weight of 16,600 pounds, and a check of the weight and balance diagram shows that the CG at station 298.0 is also within limits. [Figure 9-56]
3. Determine the landing weight and CG. This is the zero fuel
weight plus the weight of fuel at landing. [Figure 9-57]
The landing weight of 13,975 pounds is less than the
maximum landing weight of 14,000 to 16,000 pounds. According to the weight and balance diagram, the landing CG at station 297.5 is also within limits.
Introduction
Almost all weight and balance problems involve only simple
math. This allows slide rules and hand-held electronic calculators to relieve much of the tedium involved with these problems. This chapter compares the methods of determining the center of gravity (CG) of an airplane while it is being
weighed. First, it shows how to determine the CG using a simple electronic calculator, then solves the same problem using an E6-B flight computer. Finally, it shows how to solve
it using a dedicated electronic flight computer
Use of Computer for Weight
and Balance ComputationsChapter 10
10-2Figure 10-2. Weight and balance data of a typical nosewheel
airplane.Weighing Point Weight (lb) Arm (in)
2,006Right sideLeft sideNoseTotal
Figure 10-1. A typical electronic calculator is useful for solving
most types of weight and balance problems.
Examples of typical weight and balance problems (solved
with an electronic calculator) that pilots and airframe and powerplant (A&P) maintenance technicians encounter throughout their aviation endeavors are shown later in this chapter.
Electronic Calculator
Determining the CG of an airplane in inches for the main-wheel weighing points can be done with any simple electronic calculator that has addition (+), subtraction (–), multiplication (×), and division (÷) functions. [Figure 10-1] Scientifi
calculators with such additional functions as memory (M), parentheses (( )), plus or minus (+/–), exponential (y
x),
reciprocal (1/x), and percentage (%) functions allow more complex problems to be solved or simple problems to be solved using fewer steps.
According to Figure 10-2 , the weight of the nosewheel (F) is
340 pounds, the distance between main wheels and nosewheel
(L) is –78 inches, and the total weight (W) of the airplane is 2,006 pounds. L is negative because the nosewheel is ahead of the main wheels.To determine the CG, use this formula:
CG = F × L
W
= 340 × –78
2,006
Key the data into the calculator and press the equal (=) key.
The answer should read as follows:
(340)(×)(78)(+/–)(÷)(2006)(=) –13.2The arm of the nosewheel is negative, so the CG is –13.2 or
13.2 inches ahead of the main wheel weighing points.
E6-B Flight Computer
The E6-B uses a special kind of slide rule. Instead of its scales going from 1 to 10, as on a normal slide rule, both scales go from 10 to 100. The E6-B cannot be used for addition or subtraction, but it is useful for making calculations involving multiplication and division. Its accuracy is limited, but it is sufficiently accurate for most weight and balance problems.
The same problem that was just solved with the electronic
calculator can be solved on an E6-B by following these steps:
CG = F × L
W
= 340 × –78
2,006
First, multiply 340 by 78 (disregard the minus sign)
[Figure 10-3]:
• Step 1—place 10 on the inner scale (this is the index
opposite 34 on the outer scale that represents 340).
• Step 2—opposite 78 on the inner scale, read 26.5 on
the outer scale.
Determine the value of these digits by estimating:
300 × 80 = 24,000, so 340 × 78 = 26,500.
Then, divide 26,500 by 2,006 [Figure 10-4]:
10-3Figure 10-3. E6-B computer set up to multiply 340 by 78.
Figure 10-4. E6-B computer set up to divide 26,500 by 2,006.
Step 2
Step 1
Step 4
Step 3Figure 10-5. Dedicated electronic flight computers are programmed
to solve weight and balance problems, as well as flight problems.
• Step 3—on the inner scale, place 20, which represents
2,006 opposite 26.5 on the outer scale (26.5 represents
26,500).
• Step 4—opposite the index, 10, on the inner scale read
13.2 on the outer scale.
Determine the value of 13.2 by estimating:
20,000 ÷ 2000 = 10, so 26,500 ÷ 2,006 = 13.2.
The arm (–78) is negative, so the CG is also negative.
The CG is –13.2 inches or 13.2 inches ahead of the datum.
Dedicated Electronic Flight Computer
Dedicated electronic flight computers, like the one in Figure 10-5, are programmed to solve many flight problems such as wind correction, heading and ground speed, endurance, and true airspeed (TAS), as well as weight and balance problems.
The problem just solved with an electronic calculator and
an E6-B can also be solved with a dedicated flight computer using the information shown in Figure 10-2 . Each fligh
computer handles the problems in a slightly different way, but all are programmed with prompts that solicit the required data to be inputted so there is no need to memorize any formulas. Weight and arms are inputted as called for, and a running total of the weight, moment, and CG are displayed.
10-4Typical Weight and Balance Problems
A hand-held electronic calculator like the one in Figure 10-5
is a valuable tool for solving weight and balance problems. It
can be used for a variety of problems and has a high degree of accuracy. The examples given here are solved with a calculator using only the (×),(÷),(+),( – ), and (+/–) functions. If other functions are available on your calculator, some of the steps may be simplified
Determining CG in Inches From the Datum
This type of problem is solved by firs determining the
location of the CG in inches from the main wheel weighing points, then measuring this location in inches from the datum. There are four types of problems involving the location of the CG relative to the datum.
Nosewheel Airplane With Datum Ahead of the
Main Wheels
The datum (D) is 128 inches ahead of the main wheel
weighing points; the weight of the nosewheel (F) is 340 pounds, and the distance between main wheels and nosewheel (L) is 78 inches. The total weight (W) of the airplane is 2,006 pounds. Refer to Figure 3-5 on page 3-5.
Use this formula:
CG = D – F × L
W
1. Determine the CG in inches from the main wheel:
(340)(×)(78)(÷)(2006)(=) 13.2
2. Determine the CG in inches form the datum:
(128)(–)(13.2)(=) 114.8
The CG is 114.8 inches behind the datum.
Nosewheel Airplane With Datum Behind the Main
Wheels
The datum (D) is 75 inches behind the main wheel weighing
points, the weight of the nosewheel (F) is 340 pounds, and the distance between main wheels and nosewheel (L) is 78 inches. The total weight (W) of the airplane is 2,006 pounds. Refer to Figure 3-6 on page 3-5.
Use this formula:
CG = – D + F × L
W
1. Determine the CG in inches from the main wheels:
(340)(×)(78)(÷)(2006)(=) 13.22. Determine the CG in inches from the datum:
(75)(+)(13.2)(=) 88.2
The minus sign before the parenthesis in the formula
means the answer is negative. The CG is 88.2 inches
ahead of the datum (–88.2).
Tailwheel Airplane With Datum Ahead of the Main
Wheels
The datum (D) is 7.5 inches ahead of the main wheel
weighing points, the weight of the tailwheel (R) is 67 pounds, and the distance between main wheels and tailwheel (L) is 222 inches. The total weight (W) of the airplane is 1,218 pounds. Refer to Figure 3-7 on page 3-6.
Use this formula:
CG = D + R × L
W
1. Determine the CG in inches from the main wheels.
(67)(×)(222)(÷)(1218)(=) 12.2
2. Determine the CG in inches from the datum:
(7.5)(+)(12.2)(=) 19.7
The CG is 19.7 inches behind the datum.
Tailwheel Airplane With Datum Behind the Main
Wheels
The datum (D) is 80 inches behind the main wheel weighing
points, the weight of the tailwheel (R) is 67 pounds, and the distance between main wheels and tailwheel (L) is 222 inches. The total weight (W) of the airplane is 1,218 pounds. Refer to Figure 3-8 on page 3-6.
Use this formula:
CG = –D + R × L
W
1. Determine the CG in inches from the main wheels:
(67)(×)(222)(÷)(1218)(=) 12.2
2. Determine the CG in inches from the datum:
(80)(+/–)(+)(12.2)(=) –67.8
The CG is 67.8 inches ahead of the datum.( )
( )( )( )
10-5Figure 10-6. Specifications for determining the CG of an airplane using weight and arm.
Figure 10-7. Specifications for determining the CG of an airplane
using weights and moment indexes.Weight Point Weight (lb) Arm (in) Moment (lb-in) CG
106,240
107,008
17,000
230,248 114.8Right side
Left sideNoseTotal830836340
2,006128128
Weighing Point Weight (lb) Moment/100 CG
114.8Right sideLeft sideNoseTotal830836340
2,0061,062.41,070.1
2,302.5Determining CG, Given Weights, and Arms
Some weight and balance problems involve weights and arms
to determine the moments. Divide the total moment by the total weight to determine the CG. Figure 10-6 contains the
specifications for determining the CG using weights and arms.
Determine the CG by using the data in Figure 10-6 and
following these steps:
1. Determine the total weight and record this number:
(830)(+)(836)(+)(340)(=) 2,006
2. Determine the moment of each weighing point and
record them:
(830)(×)(128)(=) 106,240
(836)(×)(128)(=) 107,008
(340)(×)(50)(=) 17,000
3. Determine the total moment and divide this by the
total weight:
(106240)(+)(107008)(+)(17000)(=)(÷)(2006)(=)
This airplane weighs 2,006 pounds and its CG is 114.8 inches
from the datum.
Determining CG, Given Weights, and Moment
Indexes
Other weight and balance problems involve weights and
moment indexes, such as moment/100 or moment/1,000. To determine the CG, add all the weights and all the moment indexes. Then, divide the total moment index by the total weight and multiply the answer by the reduction factor. Figure 10-7 contains the specifications for determining the CG using weights and moments indexes.Determine the CG by using the data in Figure 10-7 and
following these steps:
1. Determine the total weight and record this number:
(830)(+)(836)(+)(340)(=) 2,006
2. Determine the total moment index, divide this by the
total weight, and multiply it by the reduction factor of 100:
(1062.4)(+)(1070.1)(+)(170)(=)(2302.5)(÷)(2006)(=)
(1.148)(×)(100)(=) 114.8
This airplane weighs 2,006 pounds and its CG is 114.8 inches
from the datum.
Determining CG in Percent Mean Aerodynamic
Chord (MAC)
• The loaded CG is 42.47 inches aft of the datum.
• MAC is 61.6 inches long.
• LEMAC is at station 20.1.
1. Determine the distance between the CG and LEMAC:
(42.47)(–)(20.1)(=) 22.37
2. Then, use this formula:
(22.37)(×)(100)(÷)(61.6)(=) 36.3
The CG of this airplane is located at 36.3 percent MAC.Determining Lateral CG of a Helicopter
For a helicopter, it is often necessary to determine not only
the longitudinal CG, but the lateral CG as well. Lateral CG is measured from butt line zero (BL 0). All items and moments to the left of BL 0 are negative, and all those to the right of BL 0 are positive. Figure 10-8 contains the specifications for
determining the lateral CG of a typical helicopter.
10-6Figure 10-8. Specifications for determining the lateral CG of a helicopter.Item Weight (lb) Lateral Arm (in) Lateral Offset Moment (lb-in) Lateral CG
−2,295
2,700
−2,419
−1,705 –0.77Helicopter empty weight
Pilot
Passenger
Fuel (48 gal)
Total1,545
2,203+0.2
+13.5
–8.4x =Determine the lateral CG by using the data in Figure 10-8 and
following these steps:
1. Add all of the weights:
(1545)(+)(170)(+)(200)(+)(288)(=) 2,203
2. Multiply the lateral arm (the distance between butt
line zero and the CG of each item) by its weight to
get the lateral offset moment of each item. Moments to the right of BL 0 are positive and those to the left are negative.
(1,545)(×)(.2)(=) 309
(170)(×)(13.5)(+/–)(=) –2,295
(200)(×)(13.5)(=) 2,700
(288)(×)(8.4)(+/–)(=) –2,419
3. Determine the algebraic sum of the lateral offset
moments.
(309)(+)(2295)(+/–)(+)(2700)(+)(2419)(+/–)(=)
–1,705
4. Divide the sum of the moments by the total weight to
determine the lateral CG.
(1705)(+/–)(÷)(2203)(=) –0.77
The lateral CG is 0.77 inch to the left of BL0.
Determining ΔCG Caused by Shifting Weights
Fifty pounds of baggage is shifted from the aft baggage
compartment at station 246 to the forward compartment at station 118. The total airplane weight is 4,709 pounds. How much does the CG shift?
1. Determine the number of inches the baggage is shifted:
(246)(–)(118)(=) 128
2. Use this formula:
Δ CG = Weight shifted × Distance weight is shifted
Total weight
(50)(×)(128)(÷)(4709)(=) 1.36
The CG is shifted forward 1.36 inches.Determining Weight Shifted to Cause Specified
ΔCG
How much weight must be shifted from the aft baggage
compartment at station 246 to the forward compartment at station 118 to move the CG forward 2 inches? The total weight of the airplane is 4,709 pounds.
1. Determine the number of inches the baggage is shifted:
Weight shifted = Total weight shifted × Δ CG
Distance weight is shifted
(246)(–)(118)(=) 128
2. Use this formula:
(2)(×)(4709)(÷)(128)(=) 73.6
Moving 73.6 pounds of baggage from the aft compartment to forward compartment shifts the CG forward 2 inches.
Determining Distance Weight Is Shifted to Move
CG a Specific Distanc
How many inches aft does a 56 pound battery need to be
moved to shift the CG aft by 1.5 inches? The total weight of the airplane is 4,026 pounds.
Use this formula:
Distance weight is shifted = Total weight
× Δ CG
Weight shifted
(1.5)(×)(4026)(÷)(56)(=) 107.8Moving the battery aft by 107.8 inches shifts the CG aft 1.5
inches.
10-7Determining Total Weight of an Aircraft With a
Specified ΔCG When Cargo Is Move
What is the total weight of an airplane if moving 500 pounds
of cargo 96 inches forward shifts the CG 2.0 inches?
Use this formula:
Total weight = Weight shifted × Distance weight is shifted
Δ CG
(500)(×)(96)(÷)(2)(=) 24,000
Moving 500 pounds of cargo 96 inches forward causes a
2.0-inch shift in CG of a 24,000-pound airplane.
Determining Amount of Ballast Needed to Move
CG to a Desired Location
How much ballast must be mounted at station 228 to move
the CG to its forward limit of +33? The airplane weighs 1,876 pounds and the CG is at +32.2, a distance of 0.8 inch out of limit.
Use this formula:
Ballast weight = Aircraft empty weight ×
D i s t . o u t o f l i m i t s
Distance ballast to desired CG
(1876)(×)(.8)(÷)(195)(=) 7.7
Attaching 7.7 pounds of ballast to the bulkhead at station
228 moves the CG to +33.0.
A-1FAA Publications
(check for most current revision)
• Advisory Circular (AC) 20-161, Aircraft Onboard Weight and Balance Systems
• AC 23-21, Airworthiness Compliance Checklists Used to Substantiate Major Alterations for Small Airplanes
• AC 43.13-1, Acceptable Methods, Techniques, and Practices—Aircraft Inspection and Repair
• AC 90-89, Amateur-Built Aircraft and Ultralight Flight Testing Handbook
• AC 120-27, Aircraft Weight and Balance Control
• FAA-H-8083-30, Aviation Maintenance Technician Handbook—General
• Order 8130.2, Airworthiness Certification of Aircraft and Related Product
• www.faa.gov, Light Sport Aircraft (multiple electronic documents)
Appendix A
Supplemental Study Materials for Aircraft Weight and Balance
A-2
B-1Station 0 Station 50Station 0 Station 7010 lb
MAC
(+)
Arm(–)
Arm(+)
Arm
(+) Arm
70"
TEMACLEMAC
Aft limitForward limitDatum
ation 50
MAC
TEM
LEM
CGCG
range
(–)
A
(+)
A
Aft lim
Forwar d
Multiengine aircraftSingle-engine aircraftDatumDatum
WeightMoment = 700 lb–in
Appendix B
Key Weight and Balance Locations on an Aircraft
B-2
G-1A note on glossary terms: over the years there has been a
proliferation of aircraft weight and balance terms. This is the result of many factors, such as the Federal Aviation Administration (FAA) certification regulation under which an aircraft was constructed; the FAA regulation under which the aircraft is being operated; manufacturer standardization agreements or a combination of these and others. Examples of such terms are empty weight, licensed empty weight, basic empty weight, operational empty weight, etc.
Many of these terms may have similar meanings or sound
similar. Pilots and aircraft mechanics must ensure they understand the terminology and are applying the correct values based on the procedure and situation dictating the calculations undertaken.
Occasionally, the acronym “GAMA” follows the glossary
term. This indicates that it is part of the standardized format adopted by the General Aviation Manufacturers Association in 1976, known as GAMA Specification No.1. These aircraft are usually manufactured under Title 14 of the Code of Federal Regulations (14 CFR) part 23 and differ from aircraft manufactured under the earlier certification rule Civil Air Regulation (CAR) part 3 for weight and balance purposes in the condition under which empty weight was established.
Aircraft certific ted under 14 CFR parts 23, 25, 27, and 29
establish their certificated empty weight as required in the appropriate section of these regulations, which states that the empty weight and corresponding center of gravity (CG) must be determined by weighting the aircraft with:
• Fixed ballast
• Unusable fuel
• Full operating flu d, including oil, hydraulic flu d,
and other fluids required for normal operation of the aircraft systems, except potable water, lavatory precharge water, and water intended for injection in the engine(s).
In contrast, aircraft certificated under the older CARs established certifi ated empty weight under similar conditions
Glossary
as the newer aircraft, with the important exception that the aircraft weight did not include full oil, only undrainable oil. Mechanics and repair stations should consult the appropriate certification rule when reestablishing empty weight
14 CFR part 121. The Federal regulations governing
domestic, flag, and supplemental operations14 CFR part 135. The Federal regulations governing
commuter and on-demand operations.Adverse loaded CG check. A weight and balance check to
determine that no condition of legal loading of an aircraft
can move the CG outside of its allowable limits.
Aircraft specifications. Documentation containing the
pertinent specifications for aircraft certificated under the
CARs.
Airplane Flight manual (AFM). An FAA-approved
document, prepared by the holder of a type certificate for an
aircraft, that specifies the operating limitations and contains the required markings and placards and other information applicable to the regulations under which the aircraft was certificated
Approved type certificate. A certificate of approval issued
by the FAA for the design of an aircraft, engine, or propeller.
Arm. (GAMA) The horizontal distance from the reference
datum to the CG of an item. The algebraic sign is plus (+) if measured aft of the datum or to the right side of the center line when considering a lateral calculation. The algebraic sign is minus (–) if measured forward of the datum or the left side of the center line when considering a lateral calculation.
Balanced laterally. Being balanced in such a way that the
aircraft wings tend to remain level.Ballast. A weight installed or carried in an aircraft to move
the center of gravity to a location within its allowable limits.
G-2Permanent ballast (fixed ballast). A weight permanently
installed in an aircraft to bring its CG into allowable limits. Permanent ballast is part of the aircraft empty weight.
Temporary ballast. Weights that can be carried in a cargo
compartment of an aircraft to move the location of CG for a specifi fl ght condition. Temporary ballast must be removed when the aircraft is weighed.
Basic empty weight. (GAMA) Standard empty weight plus
optional equipment.
Basic operating index. The moment of the airplane at its
basic operating weight divided by the appropriate reduction
factor.
Basic operating weight (BOW). The empty weight of the
aircraft plus the weight of the required crew, their baggage,
and other standard items, such as meals and potable water.
Bilge area. The lowest part of an aircraft structure in which
water and contaminants collect.Butt (or buttock) line zero. A line through the symmetrical
center of an aircraft from nose to tail. It serves as the datum
for measuring the arms used to determine the lateral CG. Lateral moments that cause the aircraft to rotate clockwise are positive (+) , and those that cause it to rotate counterclockwise are negative (–).
Calendar month. A time period used by the FAA for
certification and currency purposes. A calendar month
extends from a given day until midnight of the last day of that month.
Civil Air Regulations (CAR). The predecessor to the Federal
Aviation Regulations.CAM. The acronym for the manuals containing the
certification rules under the Civil Air RegulationsCenter of gravity (CG). (GAMA) The point at which an
airplane would balance if suspended. Its distance from the reference datum is determined by dividing the total moment by the total weight of the airplane. It is the mass center of the aircraft, or the theoretical point at which the entire weight of the aircraft is assumed to be concentrated. It may be expressed in percent of MAC (mean aerodynamic cord) or in inches from the reference datum.
Center of lift. The location along the chord line of an airfoil at
which all the lift forces produced by the airfoil are considered
to be concentrated.Centroid. The distance in inches aft of the datum of the
center of a compartment or a fuel tank for weight and balance purposes.
CG arm. (GAMA) The arm obtained by adding the airplane’s
individual moments and dividing the sum by the total weight.CG limits. (GAMA) The extreme CG locations within which
the aircraft must be operated at a given weight. These limits
are indicated on pertinent FAA aircraft type certificate data sheets, specifications, or weight and balance records
CG limits envelope. An enclosed area on a graph of the
airplane loaded weight and the CG location. If lines drawn
from the weight and CG cross within this envelope, the airplane is properly loaded.
CG moment envelope. An enclosed area on a graph of
the airplane loaded weight and loaded moment. If lines
drawn from the weight and loaded moment cross within this envelope, the airplane is properly loaded.
Chord. A straight line distance across a wing from leading
edge to trailing edge.
Curtailment. An operator created and FAA-approved
operational loading envelope that is more restrictive than
the manufacturer’s CG envelope. It ensures that the aircraft will be operated within limits during all phases of flight Curtailment typically accounts for, but is not limited to, in-flight movement of passengers and crew, service equipment, cargo variation, seating variation, etc.
Datum. An imaginary vertical plane or line from which all
measurements of arms are taken. The datum is established
by the manufacturer. Once the datum has been selected, all moment arms and the location of CG range are measured from this point.
Delta (Δ). The Greek symbol “Δ” means a change in
something. ΔCG means a change in the center of gravity
location.
Dynamic load. The actual weight of the aircraft multiplied
by the load factor, or the increase in weight caused by
acceleration.
Empty weight. The weight of the airframe, engines,
all permanently installed equipment, and unusable fuel.
Depending upon the part of the federal regulations under which the aircraft was certificated, either the undrainable oil or full reservoir of oil is included.
G-3Empty weight center of gravity (EWCG). This is the center
of gravity of the aircraft in the empty condition, containing
only the items specified in the aircraft empty weight. This CG is an essential part of the weight and balance record of the aircraft.
Empty weight center of gravity range. The distance
between the allowable forward and aft empty-weight CG
limits.
Equipment list. A list of items approved by the FAA for
installation in a particular aircraft. The list includes the name, part number, weight, and arm of the component. Installation or removal of an item in the equipment list is considered to be a minor alteration.
Fleet weight. An average weight accepted by the FAA for
aircraft of identical make and model that have the same
equipment installed. When a fleet weight control program is in effect, the fleet weight of the aircraft can be used rather than requiring every individual aircraft to be weighed.
Fuel jettison system. A fuel subsystem that allows the fligh
crew to dump fuel in an emergency to lower the weight of an
aircraft to the maximum landing weight if a return to landing is required before sufficient fuel is burned off. This system must allow enough fuel to be jettisoned that the aircraft can still meet the climb requirements specified in 14 CFR part 25.
Fulcrum. The point about which a lever balances.Index point. A location specified by the aircraft manufacturer
from which arms used in weight and balance computations
are measured. Arms measured from the index point are called index arms.
Interpolate. Determine a value in a range between two
known values.Landing weight. The takeoff weight of an aircraft minus the
fuel burned and/or dumped en route.Large aircraft (14 CFR part 1). An aircraft of more than
12,500 pounds maximum certificated takeoff weightLateral balance. The balance around the roll, or longitudinal,
axis.Lateral offset moment. The moment, in pound inches, of a
force that tends to rotate a helicopter about its longitudinal axis. The lateral offset moment is the product of the weight of the object and its distance from butt line zero. Lateral offset moments that tend to rotate the aircraft clockwise are positive, and those that tend to rotate it counterclockwise are negative.LEMAC. Leading edge of the mean aerodynamic chord. A
reference point for measurements, and specified in inches from the datum to allow computations to relate percent MAC to the datum.
Load cell. A component in an electronic weighing system that
is placed between the jack and the jack pad on the aircraft.
The load cell contains strain gauges whose resistance changes with the weight on the cell.
Load factor. The ratio of the maximum load an aircraft can
sustain to the total weight of the aircraft. Normal category
aircraft must have a load factor of a least 3.8; utility category aircraft, 4.4; and acrobatic category aircraft, 6.0.
Loading graph. A graph of load weight and load moment
indexes. Diagonal lines for each item relate the weight to the
moment index, eliminating the need for calculations.
Loading schedule. A method of calculating and documenting
aircraft weight and balance prior to taxiing to ensure the
aircraft will remain within all required weight and balance limitations throughout the flight
Longitudinal axis. An imaginary line through an aircraft
from nose to tail, passing through its center of gravity.Longitudinal balance. The balance around the pitch, or
lateral, axis.MAC. Mean aerodynamic chord.Major alteration. An alteration not listed in the aircraft,
aircraft engine, or propeller specifications (1) that might
appreciably affect weight, balance, structural strength, performance, powerplant operation, flight characteristics, or other qualities affecting airworthiness; or (2) that is not done according to accepted practices or cannot be done by elementary operations.
Maximum landing weight. (GAMA) The maximum weight
approved for the landing touchdown.Maximum permissible hoist load. The maximum external
load that is permitted for a helicopter to carry. This load is
specified in the POH
Maximum ramp weight. (GAMA) The maximum weight
approved for ground maneuver. It includes weight of start, taxi, and runup fuel.
Maximum takeoff weight. (GAMA) The maximum weight
approved for the start of the takeoff run.
G-4Maximum taxi weight. The maximum weight approved
for ground maneuvers. This is the same as maximum ramp
weight. Maximum weight. The maximum authorized weight of
the aircraft and all of its equipment as specified in the Type Certificate Data Sheets (TCDS) for the aircraft
Maximum zero fuel weight. The maximum authorized
weight of an aircraft without fuel. This is the total weight
for a particular flight minus the fuel. It includes the aircraft and everything that is carried on the flight except the weight of the fuel.
Mean aerodynamic chord (MAC). The average distance
from the leading edge to the trailing edge of the wing.METO horsepower (maximum except takeoff HP). The
maximum power allowed to be produced continuously by an
engine. Takeoff power is usually limited to a given amount of time, such as 1 minute or 5 minutes.
Minimum fuel. The amount of fuel necessary for one-half
hour of operation at the rated maximum-continuous power setting of the engine, which, for weight and balance purposes, is
1⁄12 gallon per maximum-except-takeoff (METO) horse-
power. It is the maximum amount of fuel that could be used in weight and balance computations when low fuel might adversely affect the most critical balance conditions. To determine the weight of the minimum fuel in pounds, divide the METO horsepower by two.
Minor alteration. An alteration other than a major alteration.
This includes alterations that are listed in the aircraft, aircraft
engine, or propeller specifications
Moment. A force that causes or tends to cause an object to
rotate. It is indicated by the product of the weight of an item multiplied by its arm.
Moment. (GAMA) The product of the weight of an item
multiplied by its arm. (Moment divided by a constant is used
to simplify balance calculations by reducing the number of digits; see reduction factor.)
Moment index. The moment (weight times arm) divided by
a reduction factor.
Moment limits versus weight envelope. An enclosed area on
a graph of three parameters. The diagonal line, representing
the moment/100, crosses the horizontal line, representing the weight at the vertical line, representing the CG location in inches aft of the datum. If the lines cross inside the envelope, the aircraft is loaded within its weight and CG limits.Net weight. The weight of the aircraft minus the weight of
chocks or other devices used to hold the aircraft on the scales.
Normal category. A category of aircraft certificat d under
14 CFR part 23 and CAR part 3 that allows the maximum weight and CG range while restricting the maneuvers that are permitted.
PAX. The abbreviation of passengers.Payload. (GAMA) The weight of occupants, cargo, and
baggage.Percent MAC. The distance in inches of the CG from
LEMAC divided by the MAC. It is a good standard for CG
location in airplanes because it permits a standard weight and balance program for different types of airplanes.
Pilot’s operating handbook (POH). An FAA-approved
document published by the airframe manufacturer that lists
the operating conditions for a particular model of aircraft and its engine(s).
Potable water. The water carried in an aircraft for the
purpose of drinking.Ramp weight. The zero fuel weight plus all of the usable
fuel on board.
Reference datum. (GAMA) An imaginary vertical plane
from which all horizontal distances are measured for balance
purposes.
Reduction factor. A number, usually 100 or 1,000, by which
a moment is divided to produce a smaller number that is less
likely to cause mathematical errors when computing the center of gravity.
Residual fuel. The fuel that remains trapped in the system
after draining the fuel from the aircraft with the aircraft in level flight attitude. The weight of this residual fuel is counted as part of the empty weight of the aircraft.
Service ceiling. The highest altitude at which an aircraft
can maintain a steady rate of climb of 100 feet per minute.Small aircraft (14 CFR part 1). An aircraft weighing 12,500
pounds or less maximum certificated takeoff weightStandard empty weight. (GAMA) The weight of a standard
airplane including unusable fuel, full operating fluids, and full oil.
G-5Static load. The load imposed on an aircraft structure due
to the weight of the aircraft and its contents.
Station. (GAMA) A location along the airplane fuselage
usually given in terms of distance from the reference datum.Strain sensor. A device that converts a physical phenomenon
into an electrical signal. Strain sensors in a wheel axle sense
the magnitude of the force the axle deflects and create an electrical signal that is proportional to the force that caused the deflection
Structural station. A location in the aircraft, such as a
bulkhead, that is identifi d by a number designating its
distance in inches or percent MAC from the datum. The datum is, therefore, identified as station zero. The stations and arms are identical. An item located at station +50 would have an arm of 50 inches.
Takeoff weight. The weight of an aircraft just before
beginning the takeoff roll. It is the ramp weight minus the
weight of the fuel burned during start and taxi.
Tare weight. The weight of any chocks or devices that are
used to hold an aircraft on the scales when it is weighed. The
tare weight must be subtracted from the scale reading to get the net weight of the aircraft.
TEMAC. Trailing edge of the mean aerodynamic chord.Type certificate data sheets (TCDS). The official
specifications issued by the FAA for an aircraft, engine, or
propeller.Undrainable oil. The oil that does not drain from an engine
lubricating system when the aircraft is in the normal ground attitude and the drain valve is left open. The weight of the undrainable oil is part of the empty weight of the aircraft.
Unusable fuel. (GAMA) The fuel remaining after a test has
been completed in accordance with governmental regulations.
Usable fuel. (GAMA) The fuel available for fl ght planning.
Useful load. (GAMA) The difference between takeoff
weight, or ramp weight if applicable, and basic empty weight.Utility category. A category of aircraft certificated under 14
CFR part 23 and CAR part 3 that permits limited acrobatic
maneuvers but restricts the weight and the CG range.
Wing chord. A straight line distance across a wing from
leading edge to trailing edge.Zero fuel weight. The weight of an aircraft without fuel.
G-6
A
adverse-loaded CG checks ............................................. 7-6
aft adverse-load CG check ............................................. 7-7
aircraft category ............................................................. 4-3
aircraft certificatio ........................................................ 4-3
aircraft classificatio ...................................................... 4-3
airplanes ......................................................................... 4-5
airships ........................................................................... 4-5
airworthiness certificat ......................................... 4-4, 4-8
alteration ................................................................ 7-1, 7-5
amateur-built aircraft ...................................... 4-3, 4-6, 4-8
amateur-built LSA ......................................................... 4-1
arm ................................................................ 2-2, 7-5, 10-5
B
balance ........................................................................... 1-4
control ......................................................................... 1-4
ballast ............................................................ 3-4, 7-7, 10-7
balloon ............................................................. 1-5, 1-6, 4-5
basic empty weight ................................................ 5-2, 6-2
basic weight and balance equation ................................. 2-4
C
cargo ............................................................................. 9-18
center of gravity ............................. 2-2, 3-1, 5-1, 9-1, 10-1
change ......................................................................... 7-1
configuratio ............................................................. 9-18
determining ....................................................... 3-5, 10-4
determining changes .................................................. 9-6
determining lateral CG of a helicopter ..................... 10-5
determining the loaded CG ......................................... 9-3
limits envelope ........................................................... 5-4
range ........................................................................... 2-6
range chart ................................................................ 2-10
certificates and document ............................................. 4-8
chart method ........................................................... 6-2, 6-3
Civil Aeronautical Administration ................................. 2-6
civil air regulations ................................................ 2-6, 3-4
commuter category ......................................................... 9-1
commuter category airplanes ....................................... 9-12comprehensive equipment list ...................................... 2-10
computer ...................................................................... 10-1
consensus standard ........................................................ 4-3
cyclic control ................................................................. 8-1
D
data pertinent to all model .............................................. 2-6
datum .............................................................................. 3-7
aft of the main wheels ................................................ 3-7
forward of the airplane ............................................... 3-6
dedicated electronic flight compute ............................ 10-3
determining cargo pallet loads ...................................... 9-9
determining new balance point ...................................... 2-3
determining weight ...................................................... 10-6
documenting changes ..................................................... 9-3
draining the fuel ............................................................. 3-4
E
E6-B flight compute ........................................... 10-1,10-2
effects of weight ............................................................. 1-3
electronic calculator ..................................................... 10-2
electronic load cells ........................................................ 3-2
empty weight .................................................................. 9-2
empty weight center of gravity ........ 3-2, 6-2, 7-6, 8-3, 9-2
empty weight CG range ................................................. 2-6
equipment for weighing ................................................. 3-2
equipment list .................................................. 3-4, 5-2, 7-2
EWCG formulas ............................................................. 3-6
experimental airworthiness certificat ........................... 4-6
extensive repair .............................................................. 3-2
F
FAA designee ................................................................. 4-4
finding balance poin ...................................................... 2-3
fixed-wing airplan ........................................................ 1-5
fleet operating empty weights (FOEW ........................ 9-5
floor loading limit ......................................................... 9-9
forward adverse-load CG check ..................................... 7-7
fuel capacity ................................................................... 2-6
fuel dump ..................................................................... 9-12
Index
I-2G
gliders ..................................................................... 4-1, 4-5
H
helicopter ................................................................ 1-5, 8-1
I
initial weight .................................................................. 9-2
J
jacking the aircraft ......................................................... 3-5
jacks ............................................................................... 3-5
K
kit-built aircraft .............................................................. 4-6
L
landing gear shock struts ................................................ 3-5
landing weight .............................................................. 9-10
large aircraft ................................................................... 9-1
lateral balance ........................................................ 1-4, 8-2
lateral CG ....................................................................... 8-3
lateral level ..................................................................... 3-5
law of the lever ....................................................... 2-1, 2-2
leading edge ................................................................... 3-8
leading edge mean aerodynamic chord (LEMAC) 7-6, 9-2
leveling the aircraft ........................................................ 3-5
lift ................................................................................... 1-2
light aircraft .................................................................... 1-5
lighter-than-air aircraft ........................................... 4-1, 4-5
light sport aircraft (LSA) ......................... 4-1, 4-2, 4-3, 4-6
light-sport category ................................................ 4-3, 4-4
light-sport eligible kit ..................................................... 4-3
load cell scales ............................................................... 3-2
loaded CG ...................................................................... 6-2
of a helicopter ............................................................. 8-3
loaded weight ................................................................. 6-3
loading graph method .................................................... 5-4
locating balance point. ........................................... 2-2, 2-3
location of CG ................................................................ 3-8
longitudinal CG .............................................................. 8-3
M
major alteration ...................................................... 3-2, 7-3
manual computational method ....................................... 5-2
manufacturer-furnished information ............................ 2-10
maximum amount of payload ...................................... 9-10
maximum baggage ......................................................... 2-6
maximum gross weight .................................................. 1-6
maximum weights .......................................................... 2-6mean aerodynamic chord ................................ 2-5, 3-1, 3-8
modifying the cargo ....................................................... 9-6
moment ........................................................... 2-2, 5-4, 7-5
index ................................................... 5-4, 7-5, 9-2, 10-5
limits ........................................................................... 6-3
multiengine aircraft ........................................................ 6-1
N
nosewheel airplane with datum ahead of the main
wheels .......................................................................... 10-4
nosewheel airplane with datum behind the mainwheels
.......................................................................... 10-4
nosewheel landing gear .......................................... 3-6, 3-7
number of seats .............................................................. 2-6
O
offloading carg ............................................................. 9-6
offloading passenger ..................................................... 8-3
oil ................................................................................... 3-4
capacity ....................................................................... 2-6
onboard aircraft weighing system .................................. 9-5
operational empty weight (OEW) .................................. 9-5
other fluid ..................................................................... 3-5
overloading .................................................................... 1-3
P
passengers .................................................................... 9-16
percent mean aerodynamic chord (MAC) ......6-3, 7-6, 9-3,
10-5permanent ballast
........................................................... 7-8
pilot in command ........................................................... 3-2
pilot’s operating handbook .......................................... 2-10
platform scales ............................................................... 3-2
powered parachute ............. 1-5, 1-6, 4-1, 4-3, 4-5, 4-6, 4-8
preflight plannin ........................................................... 5-2
R
ramp wheel scales .......................................................... 3-2
reestablishing the OEW ................................................. 9-5
registration certificat ..................................................... 4-8
repair ............................................................... 7-1, 7-3, 7-5
S
safety ...................................................................... 3-2, 3-5
scale preparation ............................................................ 3-3
shifting cargo ................................................................. 9-8
shifting the balance point ............................................... 2-4
shifting weight ..................................................... 2-4, 10-6
single-engine aircraft ..................................................... 5-1
solution by chart ............................................................. 2-4
I-3special airworthiness certificat ............................. 4-4, 4-6
special light-sport aircraft (SLSA) ................................. 4-5
stability ........................................................................... 1-4
standard airworthiness certificat ................................... 4-4
standard weights ............................................................. 3-4
statement of compliance ........................................ 4-3, 4-5
stress panels ................................................................... 3-5
stress plates .................................................................... 3-5
Swept-wing airplanes ..................................................... 1-5
T
tailwheel airplane with datum ahead of the main ........ 10-4
tailwheel airplane with datum behind the main ........... 10-4
tailwheel landing gear .................................................... 3-7
temperatures change ....................................................... 3-4
temporary ballast ............................................................ 7-8
formula ....................................................................... 7-8
total weight ..................................................................... 9-2
trailing edge ................................................................... 3-8
trim setting ..................................................................... 9-6
twin-engine airplane ....................................................... 6-1
type certificate data sheet ....................... 2-6, 3-8, 5-2, 7-6
typical placard ................................................................ 7-7
U
using fuel ........................................................................ 8-3
W
weighing aircraft ............................................................ 3-2
weighing procedures ...................................................... 9-2
weight ............................................................................. 1-2
changes ............................................................... 1-3, 7-5
envelope ...................................................................... 6-3
procedures .................................................................. 3-3weight and balance .......................................... 4-6, 4-8, 6-1
computations .............................................................. 4-8
control ................................................................. 1-2, 3-2
problems ................................................................... 10-4
records ........................................................................ 3-2
record .......................................................................... 7-3
theory .......................................................................... 2-2
weight and loading sheet ................................................ 4-8
weight and moment indexes ........................................... 6-3
weights ......................................................................... 10-5
weight-shift control (WSC) .................................... 4-1, 4-6
weight-shift control aircraft ............................ 1-5, 4-5, 4-6
wheels .......................................................................... 10-4
I-4
Fly GACA is an independent educational platform. It is not affiliated with, endorsed by, or operated by the General Authority of Civil Aviation (GACA) or the Government of the Kingdom of Saudi Arabia. The official and authoritative source for all civil aviation regulations, publications, and aeronautical information is always GACA. Always verify against the latest official GACA publication at gaca.gov.sa.